Skip to main content
BrewMarkBREWMARK

Comandante · Dial-in chart

Comandante C40 MK3 grind settings

On the Comandante C40 MK3, start pour over at 27 clicks, espresso at 12 clicks and French press at 35 clicks. Every other method, with the range to adjust in, is below.

Comandante C40 MK3
Dial range0 clicks – 50 clicks
ScaleClicks
BurrsConical
Filter reference28 clicks

The shape of this dial

The top line is the universal grind index every BrewMark recipe uses. The bottom line is the C40 MK3’s own dial. The connectors show how one maps onto the other.

FINECOARSEGRIND INDEX 0–100050COMANDANTE C40 MK3 DIALEspressoV60French pressCold brew
Where the lines bunch, the dial is compressed — small moves count for more

C40 MK3 grind size chart, by brew method

Start at the recommended setting, brew, then move within the range by taste. Sour or weak means go finer; bitter or harsh means go coarser. New to the C40 MK3? Start here.

Comandante C40 MK3 grind settings for espresso, moka pot, AeroPress, pour over, drip, Chemex, French press and cold brew
MethodSettingRange
EspressoFine. Aim for a 25–30s shot and adjust from there.First recipe →12 clicksestimated10 clicks – 15 clicks
Moka potFiner than filter, coarser than espresso. No tamping.Recipe →16 clicksestimated15 clicks – 18 clicks
AeroPress (short steep)For 1–2 minute recipes. Go coarser for longer steeps.Recipe →21 clicksestimated18 clicks – 25 clicks
Pour over — V60 / coneThe reference point for most published pour-over recipes.First recipe →27 clicksestimated25 clicks – 30 clicks
SiphonMedium. Short contact over steady heat, so start here and taste.29 clicksestimated27 clicks – 30 clicks
Pour over — flat bottomKalita, Orea and similar. Slightly coarser than a cone.Recipe →30 clicksestimated28 clicks – 31 clicks
Steep and release — Clever / SwitchSteep, then drain through a paper filter. If it drains slowly, go coarser.Recipe →30 clicksestimated29 clicks – 31 clicks
Drip / batch brewAutomatic brewers. Coarser to suit the longer contact time.First recipe →31 clicksestimated30 clicks – 32 clicks
CuppingMedium-coarse, for tasting side by side. Keep it the same across every bowl.31 clicksestimated30 clicks – 32 clicks
ChemexThe thick filter needs a coarser grind to avoid stalling.Recipe →32 clicksestimated31 clicks – 33 clicks
French pressCoarse. Too fine here is the usual cause of a muddy cup.First recipe →35 clicksestimated33 clicks – 37 clicks
Cold brewCoarsest setting you have. 12–18 hours of contact.Recipe →39 clicksestimated37 clicks – 42 clicks

Comandante doesn’t publish a brew-method chart we could find, so these are estimated from comparable grinders. If your C40 MK3 reads differently, tell us.

Every grinder on one grind size chart →
Comandante C40 MK3 grind size chart: espresso 12 clicks, V60 pour over 27 clicks, French press 35 clicks, and 9 more brew methods.
The Comandante C40 MK3 grind size chart as an image: every method, its setting and range, and where each sits on the dial. Download the chart (PNG).

Not yours yet?Buy a used MK3 if you brew filter by hand and want Comandante's burrs for less; espresso drinkers who dial in often should choose a finer-stepped grinder. The C40 MK3 buying guide →

New to this grinder?

Your first cup on the C40 MK3

  1. 01

    Read the dial

    Settings count clicks from zero, the finest the dial goes. Turn it finer until it stops, then count clicks back the other way.

  2. 02

    Set the starting point

    Find your brew method in the chart above and set its number. For pour over on the C40 MK3, that is 27 clicks.

  3. 03

    Brew, then taste

    Sour or thin means the grind is too coarse: go finer, to a lower number. Bitter or harsh means too fine: go coarser, to a higher number. More on fixing sour and bitter coffee.

  4. 04

    Change one thing at a time

    Make one small change to the grind and brew again, keeping the coffee, dose and water the same. The range beside each method is how far to go before something else is the problem.

Words on this pageGrind size · Conical burrs · Grind index · Extraction · Dialing in

Goes with your C40 MK3

What makes these settings work

A setting only repeats if the dose and the pour do too. Picked for how this grinder is used, not ranked, and nothing here is sponsored. Each one links to the guide that explains it.

How much room you have to adjust

Espresso → filter18clicks of adjustment across the fine half of the dial
Filter → coarse14clicks covering filter through to cold brew
Curvesplineconical burrs, fitted with a monotone curve

That is the resolution you actually have to work with on the C40 MK3. Where the number is small, a single step moves the cup more than you would expect — so change one at a time and taste before moving again.

Dialing in the C40 MK3

Mechanically close to the MK4 and dialled almost identically — the MK4 changed the axle and bearing rather than the grind geometry. Recipes quoting MK4 clicks transfer to the MK3 essentially unchanged.

Coming from another grinder?

Convert a grind setting to the C40 MK3

If a recipe quotes a setting for a different grinder, this maps it onto the C40 MK3’s dial using the same curve the chart above is built from.

Converting between two grinders that are not this one? Open the full converter.

Owners’ particle-size readings

No readings for the C40 MK3 yet. If you own one, you can measure your grind with a phone photo; readings are reviewed, then shown here.

How these numbers were worked out

Every grinder gets mapped onto a shared 0–100 grind index, where 0 is espresso-fine and 100 is the coarsest useful setting. Five reference points on the C40 MK3 are placed on that scale — espresso, moka, filter, French press and coarse — and the settings in between are interpolated.

Comandante doesn’t publish a brew-method chart for the C40 MK3 that we could find, so its reference points are estimated by comparison with grinders whose makers do. They are a starting point rather than a specification; if your C40 MK3 reads differently, tell us.

Because the C40 MK3 uses conical burrs, the curve between those points is fitted with a monotone cubic spline rather than straight lines. Conical burr dials are rarely linear, and the spline guarantees the curve never doubles back — a coarser index always produces a coarser setting.

The result is that “medium-fine” resolves to a real number on this grinder rather than a vague instruction. It is a starting point, not a guarantee — burr wear, bean density and roast level all move the target, which is why every row above gives a range as well as a number.

Own a C40 MK3? Tell us your setting

If you’ve dialled in a method on your own C40 MK3, the number you landed on is the best evidence there is. Readings are checked by hand before anything changes here.

← All grinder charts