Master chart
Coffee grind size chart for every grinder
“Medium-fine” is a different number on every grinder. This is the number, for 211 grinders and 12 ways to brew, on each grinder’s own dial. For the 77 marked maker’s chart, the settings are the maker’s own; every grinder’s page says where its numbers come from.
Coffee grind size by brew method
Where each method sits, fine to coarse
- Espresso
- Grind index 0 to 12 of 100
- 250–400 µm
- Fine. Aim for a 25–30s shot and adjust from there.
- Moka
- Grind index 12 to 20 of 100
- Finer than filter, coarser than espresso. No tamping.
- AeroPress
- Grind index 20 to 32 of 100
- For 1–2 minute recipes. Go coarser for longer steeps.
- V60
- Grind index 33 to 45 of 100
- The reference point for most published pour-over recipes.
- Siphon
- Grind index 36 to 49 of 100
- Medium. Short contact over steady heat, so start here and taste.
- Flat bottom
- Grind index 40 to 52 of 100
- Kalita, Orea and similar. Slightly coarser than a cone.
- Clever / Switch
- Grind index 42 to 55 of 100
- Steep, then drain through a paper filter. If it drains slowly, go coarser.
- Drip
- Grind index 45 to 58 of 100
- 750–900 µm
- Automatic brewers. Coarser to suit the longer contact time.
- Cupping
- Grind index 46 to 58 of 100
- 650–750 µm
- Medium-coarse, for tasting side by side. Keep it the same across every bowl.
- Chemex
- Grind index 52 to 66 of 100
- The thick filter needs a coarser grind to avoid stalling.
- French press
- Grind index 65 to 80 of 100
- Coarse. Too fine here is the usual cause of a muddy cup.
- Cold brew
- Grind index 80 to 100 of 100
- Coarsest setting you have. 12–18 hours of contact.
Particle sizes are given only where independent standards and lab measurements agree: espresso, drip and cupping. For the other methods published figures disagree, so we don’t print one. Where these come from.
Quick picks: popular grinders
The starting setting for espresso, pour over and French press on the grinders people look up most. Every other grinder and method is in the full chart below.
| Grinder | Espresso | Pour over | French press |
|---|---|---|---|
| Timemore Sculptor 0780–18 · Flat | 1 | 4 | 12.5 |
| Timemore C30–36 clicks · Conical | 9 | 15 | 22 |
| Mahlkönig EK430–16 · Flat | 3.7 | 8.8 | 14.1 |
| Comandante C40 MK40–40 clicks · Conical | 10 | 27 | 31 |
| 1Zpresso X-Ultra0–240 clicks · Conical | 57 | 133 | 175 |
| 1Zpresso JX-Pro0–200 clicks · Conical | 59 | 145 | 186 |
| 1Zpresso ZP6 Special0–90 clicks · Conical | 24 | 44 | 55 |
| KINGrinder K60–240 clicks · Conical | 44 | 100 | 150 |
| Baratza Encore1–40 · Conical | 8 | 15 | 28 |
| Fellow Ode Gen 21–11 · Flat | 1.2 | 6.2 | 9 |
| Niche Zero0–50 · Conical | 12.8 | 40 | 47.5 |
| Eureka Mignon Specialita0.0–24.0 rotations · Flat | 2.5 | 1+1.5 | 1+5.5 |
Grind settings for every grinder
Find your grinder, read across to your brew method. Numbers are on that grinder’s own dial.
| Grinder | Espresso | Moka | AeroPress | V60 | Siphon | Flat bottom | Clever / Switch | Drip | Cupping | Chemex | French press | Cold brew |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1Zpresso | ||||||||||||
| J0–120 clicks · Conical | 37 | 51 | 57 | 62 | 65 | 67 | 70 | 72 | 74 | 80 | 94 | 104 |
| J-Max0–405 clicks · Conical · maker’s chart | 123 | 194 | 229 | 259 | 272 | 283 | 296 | 240 | 313 | 338 | 383 | 399 |
| J-Max S0–450 clicks · Conical · maker’s chart | 124 | 195 | 230 | 259 | 272 | 285 | 299 | 240 | 319 | 348 | 388 | 396 |
| J-Ultra0–500 clicks · Conical · maker’s chart | 139 | 218 | 257 | 288 | 302 | 314 | 326 | 270 | 342 | 368 | 421 | 467 |
| JE0–150 clicks · Conical · maker’s chart | 54 | 71 | 87 | 104 | 108 | 111 | 113 | 90 | 115 | 118 | 126 | 139 |
| JX0–120 clicks · Conical · maker’s chart | 31 | 48 | 60 | 74 | 78 | 80 | 82 | 60 | 84 | 86 | 93 | 103 |
| JX S0–120 clicks · Conical | 37 | 51 | 57 | 62 | 65 | 67 | 70 | 72 | 74 | 80 | 94 | 104 |
| JX-Pro0–200 clicks · Conical · maker’s chart | 59 | 96 | 120 | 145 | 151 | 156 | 160 | 120 | 165 | 172 | 186 | 194 |
| JX-Pro S0–200 clicks · Conical · maker’s chart | 60 | 96 | 120 | 145 | 151 | 156 | 160 | 120 | 166 | 173 | 185 | 193 |
| K-Max0–180 clicks · Conical · maker’s chart | 39 | 54 | 68 | 82 | 84 | 85 | 86 | 70 | 86 | 88 | 97 | 138 |
| K-Plus0–180 clicks · Conical · maker’s chart | 39 | 54 | 68 | 82 | 84 | 85 | 86 | 70 | 86 | 88 | 97 | 138 |
| K-Pro0–180 clicks · Conical · maker’s chart | 40 | 54 | 67 | 82 | 85 | 87 | 88 | 70 | 89 | 90 | 97 | 114 |
| K-Ultra0–100 clicks · Conical · maker’s chart | 39 | 54 | 67 | 82 | 85 | 87 | 88 | 70 | 90 | 92 | 95 | 98 |
| Q Air0–120 clicks · Conical · maker’s chart | 44 | 45 | 53 | 72 | 76 | 79 | 82 | 60 | 86 | 91 | 95 | 95 |
| Q20–100 clicks · Conical · maker’s chart | 44 | 44 | 53 | 72 | 76 | 78 | 80 | 60 | 82 | 85 | 88 | 89 |
| Q2 S0–120 clicks · Conical · maker’s chart | 44 | 45 | 53 | 72 | 76 | 79 | 82 | 60 | 86 | 91 | 95 | 95 |
| X-Pro0–240 clicks · Conical · maker’s chart | 57 | 80 | 104 | 133 | 140 | 145 | 149 | 110 | 154 | 161 | 175 | 187 |
| X-Pro S0–240 clicks · Conical · maker’s chart | 57 | 80 | 104 | 133 | 140 | 145 | 149 | 110 | 154 | 161 | 175 | 187 |
| X-Ultra0–240 clicks · Conical · maker’s chart | 57 | 80 | 104 | 133 | 140 | 144 | 148 | 110 | 152 | 157 | 175 | 211 |
| ZP60–70 clicks · Conical | 8 | 19 | 24 | 27 | 29 | 31 | 34 | 35 | 37 | 42 | 52 | 60 |
| ZP6 Special0–90 clicks · Conical · maker’s chart | 24 | 32 | 38 | 44 | 46 | 47 | 47 | 48 | 48 | 49 | 55 | 74 |
| Acaia | ||||||||||||
| Orbit0–19 · Flat | 4.5 | 6.2 | 6.8 | 7.6 | 7.9 | 8.3 | 8.7 | 8.9 | 9.1 | 9.9 | 11.5 | 12.7 |
| Anfim | ||||||||||||
| Best0–28 | 3.2 | 6.1 | 7.1 | 8.5 | 9.1 | 9.7 | 10.3 | 10.7 | 11.1 | 12.4 | 15.1 | 17.1 |
| Balmuda | ||||||||||||
| Coffee Mill1–22 clicks | 5 | 7 | 8 | 9 | 9 | 10 | 10 | 11 | 11 | 12 | 14 | 15 |
| Baratza | ||||||||||||
| Encore1–40 · Conical · maker’s chart | 8 | 11 | 12 | 15 | 16 | 17 | 18 | 18 | 19 | 20 | 28 | 34 |
| Encore ESP1–40 · Conical · maker’s chart | 15 | 19 | 22 | 25 | 26 | 27 | 28 | 28 | 28 | 30 | 32 | 34 |
| Forte AP1–260 · Flat · maker’s chart | 37 | 58 | 91 | 143 | 149.4 | 159 | 168.7 | 169 | 181.6 | 195 | 247 | 251 |
| Forté BG1–260 · Flat · maker’s chart | 2K | 3G | 4M | 6M | 6S | 7B | 7L | 7M | 7Y | 8M | 10M | 10R |
| Maestro1–40 · Conical · maker’s chart | 7.5 | 13.5 | 15.8 | 17.7 | 19.3 | 20.9 | 22.7 | 24.1 | 25.5 | 29.7 | 36.8 | 38.8 |
| Maestro Plus1–40 · Conical · maker’s chart | 7.5 | 13.7 | 15.5 | 16.8 | 18 | 19.3 | 20.8 | 22 | 23.3 | 27.2 | 34.5 | 37.7 |
| Preciso1–440 · Conical | 61.1 | 116.4 | 140.6 | 160.8 | 172.5 | 183.2 | 195 | 203.3 | 211.9 | 238.3 | 292.5 | 334.4 |
| Sette 2701–31 · Conical · maker’s chart | 6 | 10 | 12 | 15 | 16 | 18 | 19 | 21 | 22 | 25 | 29 | 29 |
| Sette 270W1–31 · Conical · maker’s chart | 6 | 10.2 | 12.5 | 15.2 | 16.5 | 17.9 | 19.5 | 20.6 | 21.8 | 25.2 | 29.4 | 30 |
| Sette 270Wi1–31 · Conical · maker’s chart | 6 | 9 | 12 | 16 | 17 | 18 | 19 | 19 | 20 | 22 | 25 | 27 |
| Sette 301–31 · Conical · maker’s chart | 8.4 | 12.3 | 13.3 | 14.2 | 14.9 | 15.8 | 16.9 | 17.7 | 18.5 | 21.3 | 26.5 | 29.3 |
| Starbucks Barista1–40 · Conical · maker’s chart | 7.5 | 13.5 | 15.8 | 17.7 | 19.3 | 20.9 | 22.7 | 24.1 | 25.5 | 29.7 | 36.8 | 38.8 |
| Vario+1–130 · Flat | 2Q | 2S | 4M | 6M | 6T | 7L | 7P | 7S | 7V | 8S | 10M | 10R |
| Virtuoso0–40 · Conical · maker’s chart | 8 | 10.3 | 12 | 15 | 15.5 | 16.4 | 17.4 | 18 | 18.9 | 20 | 28 | 34 |
| Virtuoso+1–40 · Conical · maker’s chart | 8 | 11 | 12 | 15 | 16 | 17 | 18 | 18 | 19 | 20 | 28 | 34 |
| Barista & Co | ||||||||||||
| Core All Grind0–40 | 6.3 | 12.6 | 14.8 | 17.6 | 18.9 | 20.2 | 21.5 | 22.4 | 23.2 | 25.9 | 31.7 | 36.1 |
| Barista Space | ||||||||||||
| Premium Coffee Hand Grinder0–48 clicks | 14 | 19 | 21 | 24 | 25 | 26 | 27 | 28 | 28 | 31 | 36 | 39 |
| Bodum | ||||||||||||
| Bistro 109031–12 · Conical | 1.3 | 2 | 2.4 | 3 | 3.2 | 3.5 | 3.8 | 4 | 4.2 | 4.8 | 6.2 | 7.1 |
| Breville | ||||||||||||
| Barista Express (built-in)1–16 · Conical · maker’s chart | 5 | 6 | 7 | 9 | 9 | 9 | 10 | 10 | 10 | 11 | 12 | 13 |
| Barista Express Impress (built-in)1–25 · Conical · maker’s chart | 16 | 17 | 17 | 17 | 17 | 17 | 17 | 17 | 17 | 18 | 18 | 20 |
| Barista Touch Impress (built-in)1–30 · Conical | 6 | 10 | 13 | 16 | 17 | 17 | 18 | 18 | 19 | 20 | 22 | 25 |
| Dose Control Pro1–60 · Conical · maker’s chart | 15 | 23 | 28 | 34 | 36 | 37 | 39 | 40 | 41 | 44 | 50 | 56 |
| Smart Grinder Pro1–60 · Conical · maker’s chart | 12 | 16 | 23 | 41 | 44 | 46 | 48 | 50 | 51 | 54 | 58 | 58 |
| Cafflano | ||||||||||||
| Grinder1–16 clicks | 6 | 8 | 9 | 10 | 10 | 11 | 11 | 11 | 12 | 12 | 14 | 15 |
| Capresso | ||||||||||||
| Infinity1–16 · Conical | 2.4 | 4.3 | 5.1 | 5.8 | 6.2 | 6.6 | 7 | 7.2 | 7.5 | 8.4 | 10.2 | 11.6 |
| Infinity Plus1–16 · Conical | 2.4 | 4.3 | 5.1 | 5.8 | 6.2 | 6.6 | 7 | 7.2 | 7.5 | 8.4 | 10.2 | 11.6 |
| Ceado | ||||||||||||
| E37S0–50 · Flat | 7.7 | 13 | 17.8 | 24 | 25.7 | 26.7 | 27.7 | 28.3 | 29 | 31 | 35.7 | 41 |
| Comandante | ||||||||||||
| C40 MK30–50 clicks · Conical | 12 | 16 | 21 | 27 | 29 | 30 | 30 | 31 | 31 | 32 | 35 | 39 |
| C40 MK40–40 clicks · Conical · maker’s chart | 10 | 17 | 22 | 27 | 28 | 28 | 29 | 29 | 29 | 29 | 31 | 34 |
| C40 MK4 (Red Clix)0–80 clicks · Conical · maker’s chart | 20 | 33 | 41 | 50 | 52 | 54 | 55 | 56 | 57 | 60 | 66 | 74 |
| C60 Baracuda0–55 clicks · Conical · maker’s chart | 14 | 24 | 29 | 34 | 36 | 37 | 38 | 38 | 39 | 41 | 45 | 51 |
| C60 Baracuda (Gold Clix)0–55 clicks · Conical · maker’s chart | 14 | 23 | 29 | 34 | 36 | 37 | 38 | 38 | 39 | 41 | 45 | 51 |
| X25 Trailmaster0–40 clicks · Conical | 13 | 17 | 19 | 21 | 22 | 22 | 23 | 24 | 24 | 26 | 31 | 34 |
| X25 Trailmaster (Red Clix)0–80 clicks · Conical | 25 | 34 | 38 | 41 | 43 | 45 | 46 | 48 | 49 | 53 | 61 | 69 |
| Compak | ||||||||||||
| K3 Push0–30 · Flat | 1.8 | 5.3 | 6.6 | 8.3 | 9.1 | 9.9 | 10.7 | 11.2 | 11.7 | 13.3 | 16.7 | 19.4 |
| K3 Touch0–30 · Flat | 1.8 | 5.3 | 6.6 | 8.3 | 9.1 | 9.9 | 10.7 | 11.2 | 11.7 | 13.3 | 16.7 | 19.4 |
| K3 Touch Advanced0–30 · Flat | 1.8 | 5.3 | 6.6 | 8.3 | 9.1 | 9.9 | 10.7 | 11.2 | 11.7 | 13.3 | 16.7 | 19.4 |
| Cuisinart | ||||||||||||
| CBM-181–18 · Conical · maker’s chart | 3.4 | 3.4 | 3.9 | 5.8 | 6.7 | 7.6 | 8.6 | 9.4 | 10.2 | 12.6 | 15.2 | 15.3 |
| DBM-8 SupremeStepless · Flat | No single setting holds across units. How to dial it in instead | |||||||||||
| DF64 | ||||||||||||
| DF64 Gen 20–90 · Flat · maker’s chart | 17.5 | 27.6 | 35 | 64.4 | 68 | 68.5 | 69 | 69.4 | 69.8 | 70.8 | 74.1 | 83.1 |
| DF64 V20–90 · Flat · maker’s chart | 17.4 | 27.7 | 35 | 64.5 | 68 | 68.5 | 68.9 | 69.2 | 69.5 | 70.5 | 73.5 | 82.9 |
| De'Longhi | ||||||||||||
| KG790–16 clicks · Flat | 1 | 2 | 3 | 4 | 4 | 5 | 5 | 5 | 6 | 6 | 8 | 10 |
| KG890–16 clicks · Flat | 1 | 2 | 3 | 4 | 4 | 5 | 5 | 5 | 6 | 6 | 8 | 10 |
| Etzinger | ||||||||||||
| etz-I (Regular)1–23 · Conical | 4.8 | 7.4 | 8.5 | 9.4 | 10 | 10.5 | 11.1 | 11.5 | 11.9 | 13.2 | 15.8 | 17.8 |
| etz-I (Trim)1–23 · Conical | 4.8 | 7.4 | 8.5 | 9.4 | 10 | 10.5 | 11.1 | 11.5 | 11.9 | 13.2 | 15.8 | 17.8 |
| etz-U1–23 · Conical | 4.8 | 7.4 | 8.5 | 9.4 | 10 | 10.5 | 11.1 | 11.5 | 11.9 | 13.2 | 15.8 | 17.8 |
| Eureka | ||||||||||||
| Atom 600.0–30.0 rotations · Flat | 4 | 1+1 | 1+2 | 1+3.5 | 1+4 | 1+4.5 | 1+5.5 | 2+0 | 2+0 | 2+1.5 | 2+4.5 | 3+0.5 |
| Atom 750.0–30.0 rotations · Flat | 3.5 | 1+1 | 1+2 | 1+3 | 1+3.5 | 1+5 | 2+0 | 2+0.5 | 2+1.5 | 2+3.5 | 3+2.5 | 4+1.5 |
| Drogheria MCD40–8 · Flat | 2.1 | 3.5 | 4 | 4.6 | 4.9 | 5.2 | 5.4 | 5.6 | 5.8 | 6.4 | 7.5 | 7.8 |
| Mignon Classico0–12 · Flat | 1.3 | 2.6 | 3 | 3.6 | 3.9 | 4.1 | 4.4 | 4.6 | 4.7 | 5.3 | 6.4 | 7.3 |
| Mignon Libra0.0–24.0 rotations · Flat | 2.5 | 4 | 5.5 | 1+1.5 | 1+2 | 1+2.5 | 1+3 | 1+3 | 1+3.5 | 1+4 | 1+5.5 | 2+1.5 |
| Mignon Silenzio0.0–24.0 rotations · Flat | 2.5 | 4 | 5.5 | 1+1.5 | 1+2 | 1+2.5 | 1+3 | 1+3 | 1+3.5 | 1+4 | 1+5.5 | 2+1.5 |
| Mignon Single Dose0.0–24.0 rotations · Flat | 2.5 | 4 | 5.5 | 1+1.5 | 1+2 | 1+2.5 | 1+3 | 1+3 | 1+3.5 | 1+4 | 1+5.5 | 2+1.5 |
| Mignon Specialita0.0–24.0 rotations · Flat | 2.5 | 4 | 5.5 | 1+1.5 | 1+2 | 1+2.5 | 1+3 | 1+3 | 1+3.5 | 1+4 | 1+5.5 | 2+1.5 |
| Oro Mignon XL0.0–24.0 rotations · Flat | 2.5 | 4 | 5.5 | 1+1.5 | 1+2 | 1+2.5 | 1+3 | 1+3 | 1+3.5 | 1+4 | 1+5.5 | 2+1.5 |
| Fellow | ||||||||||||
| Ode Gen 11–11 · Flat · maker’s chart | 1.1 | 1.2 | 2.2 | 3.1 | 4 | 4.1 | 4.2 | 5 | 3 | 6.1 | 8 | 9.2 |
| Ode Gen 21–11 · Flat · maker’s chart | 1.2 | 3 | 4.2 | 6.2 | 7 | 7.1 | 7.1 | 7.2 | 7 | 8 | 9 | 10 |
| Opus1–11 · Conical · maker’s chart | 1.2 | 1.3 | 3.2 | 6.3 | 7.2 | 7.3 | 8 | 8 | 8 | 8.2 | 9 | 10 |
| Fiorenzato | ||||||||||||
| AllGround0–73 · Flat | 20 | 40 | 43.2 | 47.4 | 49.5 | 51.7 | 53.9 | 55.3 | 56.8 | 61.2 | 70.2 | 71.8 |
| Allground Sense0–73 · Flat | 23.9 | 39.2 | 44.5 | 51.4 | 53.9 | 55.9 | 58 | 59.3 | 60.7 | 64.8 | 73 | 73 |
| Pietro (B-Modal Burrs)0–10 · Flat | 2.1 | 3.8 | 4.4 | 5.2 | 5.5 | 5.9 | 6.2 | 6.5 | 6.7 | 7.4 | 8.9 | 9.5 |
| Pietro (M-Modal Burrs)0–10 · Flat | 1.3 | 3 | 3.6 | 4.4 | 4.7 | 5.1 | 5.4 | 5.7 | 5.9 | 6.6 | 8.1 | 9.2 |
| Flair | ||||||||||||
| Royal Grinder0–72 clicks · Conical | 17 | 23 | 26 | 28 | 30 | 31 | 32 | 33 | 34 | 38 | 44 | 48 |
| Fuji Royal | ||||||||||||
| R-2201–10 · Flat · maker’s chart | 2 | 4 | 4.2 | 4.4 | 4.6 | 4.8 | 5.1 | 5.2 | 5.4 | 5.9 | 7 | 8.2 |
| Goat Story | ||||||||||||
| Arco0–240 clicks · Conical | 57 | 78 | 87 | 95 | 99 | 103 | 108 | 111 | 114 | 124 | 144 | 160 |
| Handground | ||||||||||||
| Precision Coffee Grinder1–8 · Conical · maker’s chart | 1.5 | 2.5 | 2.5 | 3.5 | 3.5 | 3.7 | 4.1 | 4.3 | 4.5 | 5 | 7 | 6.5 |
| Hario | ||||||||||||
| Mini Mill Slim0–20 clicks · Conical | 2 | 4 | 5 | 6 | 6 | 7 | 7 | 7 | 8 | 8 | 10 | 12 |
| Mini Mill Slim PRO0–20 clicks · Conical | 2 | 4 | 5 | 6 | 6 | 7 | 7 | 7 | 8 | 8 | 10 | 12 |
| Mini Mill Slim+0–15 clicks · Conical | 3 | 4 | 6 | 8 | 8 | 9 | 9 | 9 | 9 | 10 | 11 | 13 |
| Skerton1–9 clicks · Conical | 1 | 2 | 2 | 3 | 3 | 3 | 4 | 4 | 4 | 4 | 5 | 6 |
| Skerton Plus1–9 clicks · Conical | 1 | 2 | 2 | 3 | 3 | 3 | 4 | 4 | 4 | 4 | 5 | 6 |
| Skerton Pro0–15 clicks · Conical | 3 | 4 | 6 | 8 | 8 | 9 | 9 | 9 | 9 | 10 | 11 | 13 |
| Smart G1–14 clicks · Conical | 2 | 3 | 4 | 5 | 5 | 6 | 6 | 6 | 6 | 7 | 8 | 9 |
| V60 Electric Coffee Grinder (EVCG-8B-E)1–44 · Conical | 4.5 | 11 | 14.5 | 18.3 | 20.3 | 22.1 | 24.1 | 25.5 | 27 | 31.5 | 39.6 | 42.6 |
| V60 Electric Coffee Grinder Compact (EVC-8B)0–10 · Conical · maker’s chart | 2 | 3.7 | 4.5 | 5.2 | 5.6 | 6 | 6.4 | 6.7 | 7 | 7.9 | 8.9 | 8.9 |
| Helor | ||||||||||||
| 1010–80 clicks · Conical | 19 | 26 | 29 | 31 | 33 | 34 | 36 | 37 | 38 | 41 | 48 | 53 |
| HeyCafé | ||||||||||||
| H10–8 · maker’s chart | 2 | 3.1 | 3.5 | 4.1 | 4.3 | 4.6 | 4.8 | 4.9 | 5.1 | 5.5 | 6.5 | 7.1 |
| Hongbei | ||||||||||||
| Coffee Grinder0–32 clicks | 7 | 10 | 11 | 13 | 13 | 14 | 15 | 15 | 15 | 17 | 19 | 21 |
| JavaPresse | ||||||||||||
| Manual Burr Grinder0–18 clicks · Conical | 4 | 5 | 6 | 8 | 8 | 9 | 9 | 10 | 10 | 11 | 13 | 15 |
| Joy Resolve | ||||||||||||
| Groove Compact0–39 clicks · Conical | 4 | 8 | 10 | 12 | 12 | 13 | 14 | 15 | 15 | 17 | 21 | 24 |
| KINGrinder | ||||||||||||
| K00–140 clicks · Conical · maker’s chart | 68 | 68 | 72 | 87 | 92 | 97 | 104 | 108 | 113 | 126 | 140 | 140 |
| K10–140 clicks · Conical · maker’s chart | 48 | 66 | 76 | 86 | 91 | 97 | 103 | 108 | 112 | 126 | 140 | 140 |
| K20–140 clicks · Conical · maker’s chart | 51 | 66 | 75 | 86 | 92 | 97 | 103 | 108 | 112 | 126 | 140 | 140 |
| K30–140 clicks · Conical | 45 | 62 | 69 | 75 | 79 | 82 | 86 | 88 | 91 | 99 | 115 | 127 |
| K40–240 clicks · Conical · maker’s chart | 75 | 98 | 114 | 130 | 136 | 141 | 147 | 151 | 155 | 166 | 180 | 181 |
| K50–140 clicks · Conical | 45 | 62 | 69 | 75 | 79 | 82 | 86 | 88 | 91 | 99 | 115 | 127 |
| K60–240 clicks · Conical · maker’s chart | 44 | 68 | 83 | 100 | 106 | 110 | 115 | 119 | 122 | 132 | 150 | 157 |
| P00–130 clicks · Conical | 31 | 42 | 47 | 51 | 53 | 56 | 58 | 60 | 62 | 67 | 78 | 87 |
| P10–130 clicks · Conical | 31 | 42 | 47 | 51 | 53 | 56 | 58 | 60 | 62 | 67 | 78 | 87 |
| P20–130 clicks · Conical | 31 | 42 | 47 | 51 | 53 | 56 | 58 | 60 | 62 | 67 | 78 | 87 |
| Kafatek | ||||||||||||
| Monolith ConicalStepless · Conical | No single setting holds across units. How to dial it in instead | |||||||||||
| Monolith Flat MaxStepless · Flat | No single setting holds across units. How to dial it in instead | |||||||||||
| Kaldi | ||||||||||||
| Ceramic Coffee Mill0.0–1.2 rotations · Conical | 0.3 | 0.4 | 0.5 | 0.5 | 0.5 | 0.5 | 0.5 | 0.6 | 0.6 | 0.6 | 0.7 | 0.8 |
| Kalita | ||||||||||||
| C-901–9 · Conical | 1.1 | 1.4 | 1.7 | 2.1 | 2.3 | 2.5 | 2.6 | 2.8 | 2.9 | 3.3 | 4.1 | 4.7 |
| DIA Coffee Mill0.0–1.3 rotations · Conical | 0.3 | 0.4 | 0.5 | 0.5 | 0.5 | 0.5 | 0.5 | 0.6 | 0.6 | 0.6 | 0.7 | 0.8 |
| Next G1–11 | 1 | 1 | 1.4 | 1.9 | 2.2 | 2.5 | 2.8 | 3 | 3.2 | 3.7 | 5 | 6 |
| Nice Cut G1–8 · Flat | 1.1 | 1.2 | 1.5 | 1.9 | 2.1 | 2.3 | 2.5 | 2.6 | 2.8 | 3.1 | 4 | 4.6 |
| Kanso | ||||||||||||
| Hiku0–2.2 · Conical | 0.9 | 1.2 | 1.3 | 1.4 | 1.4 | 1.5 | 1.6 | 1.6 | 1.7 | 1.9 | 2.1 | 2.2 |
| Kinu | ||||||||||||
| M47 Classic0–100 clicks · Conical | 14 | 22 | 31 | 43 | 47 | 49 | 51 | 52 | 53 | 57 | 65 | 77 |
| M47 Phoenix0–100 clicks · Conical | 14 | 22 | 31 | 43 | 47 | 49 | 51 | 52 | 53 | 57 | 65 | 77 |
| M47 Simplicity0.0–8.5 rotations · Conical | 2 | 3 | 3 | 3.5 | 3.5 | 3.5 | 4 | 4 | 4 | 4.5 | 5 | 5.5 |
| M47 Traveler0.0–8.5 rotations · Conical | 2 | 3 | 3 | 3.5 | 3.5 | 3.5 | 4 | 4 | 4 | 4.5 | 5 | 5.5 |
| Krups | ||||||||||||
| GVX11–17 · Flat | 1.8 | 3.3 | 4.5 | 6.2 | 6.9 | 7.6 | 8.3 | 8.8 | 9.3 | 10.8 | 13.9 | 15.7 |
| GVX21–17 · Flat | 1.8 | 3.3 | 4.5 | 6.2 | 6.9 | 7.6 | 8.3 | 8.8 | 9.3 | 10.8 | 13.9 | 15.7 |
| GX50001–12 · Flat | 1.3 | 1.9 | 2.4 | 3 | 3.3 | 3.6 | 3.9 | 4.1 | 4.3 | 4.8 | 6.1 | 7.1 |
| GX60001–16 · Flat | 1.2 | 1.5 | 2.2 | 3.1 | 3.5 | 3.9 | 4.3 | 4.6 | 4.8 | 5.7 | 7.5 | 8.9 |
| MHW-3BOMBER | ||||||||||||
| Blade R30–180 clicks · Conical | 30 | 51 | 61 | 69 | 74 | 78 | 82 | 86 | 89 | 99 | 121 | 137 |
| Mahlkönig | ||||||||||||
| EK430–16 · Flat | 3.7 | 7 | 7.8 | 8.8 | 9.3 | 9.8 | 10.3 | 10.7 | 11 | 12 | 14.1 | 15.2 |
| EK43 (1-11 dial)1–11 · Flat | 3.3 | 5.4 | 5.9 | 6.5 | 6.8 | 7.1 | 7.5 | 7.7 | 7.9 | 8.5 | 9.8 | 10.5 |
| EK43 S0–16 · Flat | 3.7 | 7 | 7.8 | 8.8 | 9.3 | 9.8 | 10.3 | 10.7 | 11 | 12 | 14.1 | 15.2 |
| GH2 (HC880)0–17 · Flat | 4 | 6.1 | 6.8 | 7.8 | 8.2 | 8.6 | 9.1 | 9.4 | 9.7 | 10.5 | 12.5 | 14 |
| VTA 6S1–13 | 3.5 | 5.4 | 6.1 | 7 | 7.4 | 7.8 | 8.2 | 8.5 | 8.7 | 9.6 | 11.3 | 12.3 |
| VTA 6S W1–13 | 3.5 | 5.4 | 6.1 | 7 | 7.4 | 7.8 | 8.2 | 8.5 | 8.7 | 9.6 | 11.3 | 12.3 |
| X541–35 · Flat · maker’s chart | 3.1 | 7.4 | 12.9 | 20 | 21.7 | 22.5 | 23.3 | 23.9 | 24.5 | 26.1 | 29.9 | 32.8 |
| Mavo | ||||||||||||
| Phantox Pro0–120 clicks · Conical | 33 | 46 | 51 | 55 | 57 | 60 | 62 | 64 | 66 | 72 | 84 | 94 |
| Mazzer | ||||||||||||
| MiniStepless · Flat | No single setting holds across units. How to dial it in instead | |||||||||||
| Super JollyStepless · Flat | No single setting holds across units. How to dial it in instead | |||||||||||
| Melitta | ||||||||||||
| Calibra1–39 · maker’s chart | 3 | 4.9 | 9.7 | 15.8 | 17.9 | 19.4 | 21 | 22.1 | 23.1 | 26.3 | 32.6 | 26 |
| Molino1–17 | 2.8 | 5.1 | 5.9 | 7 | 7.5 | 8 | 8.5 | 8.8 | 9.1 | 10.1 | 12.2 | 13.9 |
| MiiCoffee | ||||||||||||
| D40+0–8 | 2.1 | 3.2 | 3.6 | 4.1 | 4.4 | 4.6 | 4.8 | 5 | 5.2 | 5.6 | 6.7 | 7.4 |
| Moccamaster | ||||||||||||
| KM51–9 · maker’s chart | 1.1 | 1.4 | 2.6 | 4.2 | 4.5 | 4.6 | 4.8 | 4.9 | 5 | 5.2 | 5.9 | 6.5 |
| Niche | ||||||||||||
| Duo0–50 · Flat · maker’s chart | 5.2 | 15.1 | 24.9 | 37.6 | 40.1 | 40.9 | 41.7 | 42.2 | 42.7 | 44.2 | 47.5 | 48.9 |
| Zero0–50 · Conical · maker’s chart | 12.8 | 24.7 | 32.7 | 40 | 41.7 | 42.8 | 43.6 | 44.1 | 44.5 | 45.6 | 47.5 | 49 |
| Normcore | ||||||||||||
| Manual V20–60 clicks · Conical | 11 | 16 | 22 | 29 | 31 | 32 | 33 | 34 | 34 | 36 | 41 | 47 |
| OXO | ||||||||||||
| Brew Conical Burr1–15 · Conical · maker’s chart | 3.4 | 7 | 7.3 | 7.4 | 7.5 | 7.8 | 8.2 | 8.6 | 9 | 10.3 | 12.6 | 13.2 |
| Option-O | ||||||||||||
| Lagom Casa0–30 · Conical | 7.2 | 9.8 | 10.9 | 11.8 | 12.4 | 12.9 | 13.5 | 13.9 | 14.3 | 15.5 | 18.1 | 20.1 |
| Lagom Mini0–50 · Conical | 6.3 | 11 | 15.6 | 21.2 | 22.8 | 23.9 | 24.9 | 25.6 | 26.2 | 28.2 | 32.7 | 38 |
| Lagom P1000–10 · Flat · maker’s chart | 1.5 | 3.4 | 4.8 | 6.5 | 6.9 | 7.2 | 7.4 | 7.5 | 7.6 | 8.1 | 9 | 9.1 |
| Lagom P640–10 · Flat · maker’s chart | 1.1 | 2.2 | 3.6 | 5.4 | 5.7 | 5.8 | 5.9 | 5.9 | 5.9 | 6.1 | 6.4 | 7.5 |
| Pinecone | ||||||||||||
| Pinion0–36 clicks | 1 | 4 | 6 | 8 | 9 | 10 | 10 | 11 | 12 | 13 | 17 | 21 |
| Porlex | ||||||||||||
| Mini (original)0–12 clicks · Conical | 3 | 4 | 5 | 5 | 5 | 5 | 6 | 6 | 6 | 6 | 7 | 8 |
| Mini II0–18 clicks · Conical | 5 | 6 | 8 | 10 | 10 | 11 | 11 | 11 | 11 | 12 | 13 | 15 |
| Tall (original)0–12 clicks · Conical | 3 | 4 | 5 | 5 | 5 | 5 | 6 | 6 | 6 | 6 | 7 | 8 |
| Tall II0–18 clicks · Conical | 5 | 6 | 8 | 10 | 10 | 11 | 11 | 11 | 11 | 12 | 13 | 15 |
| Precision | ||||||||||||
| GS300–14 | 1.2 | 2.7 | 3.2 | 3.9 | 4.2 | 4.5 | 4.9 | 5.1 | 5.3 | 5.9 | 7.3 | 8.4 |
| ROK | ||||||||||||
| GrinderGC0–25 clicks · Conical · maker’s chart | 5 | 12 | 14 | 15 | 15 | 15 | 15 | 15 | 16 | 16 | 18 | 16 |
| Rancilio | ||||||||||||
| Rocky0–55 · Flat | 8 | 13 | 18 | 24 | 26 | 27 | 28 | 29 | 30 | 32 | 38 | 44 |
| Rocky SD0–55 · Flat | 8 | 15.6 | 18.2 | 21.7 | 23.3 | 24.9 | 26.5 | 27.5 | 28.6 | 31.8 | 38.9 | 44.3 |
| Rocket | ||||||||||||
| Faustino0–18 · Flat | 3 | 5 | 7 | 9.6 | 10.2 | 10.5 | 10.8 | 11 | 11.2 | 11.8 | 13.2 | 14.8 |
| Saint Anthony Industries | ||||||||||||
| Millwright0–98 clicks · Conical | 24 | 32 | 36 | 39 | 41 | 43 | 44 | 46 | 47 | 51 | 59 | 66 |
| Smeg | ||||||||||||
| CGF010–30 · Conical | 2.6 | 6.8 | 8.6 | 10.1 | 11 | 11.8 | 12.6 | 13.3 | 13.9 | 15.8 | 19.9 | 23 |
| CGF110–30 · Conical | 2.6 | 6.8 | 8.6 | 10.1 | 11 | 11.8 | 12.6 | 13.3 | 13.9 | 15.8 | 19.9 | 23 |
| Timemore | ||||||||||||
| C20–36 clicks · Conical | 9 | 12 | 14 | 16 | 16 | 17 | 18 | 18 | 18 | 20 | 22 | 25 |
| C2 Max0–36 clicks · Conical | 9 | 12 | 15 | 20 | 21 | 21 | 22 | 22 | 22 | 23 | 25 | 29 |
| C30–36 clicks · Conical | 9 | 12 | 13 | 15 | 15 | 16 | 17 | 17 | 18 | 19 | 22 | 25 |
| C3S0–36 clicks · Conical | 9 | 12 | 13 | 15 | 15 | 16 | 17 | 17 | 18 | 19 | 22 | 25 |
| Chestnut C2 Fold0–30 clicks · Conical | 10 | 14 | 16 | 18 | 18 | 19 | 20 | 21 | 21 | 23 | 26 | 29 |
| Chestnut C2 Max Pro0–30 clicks · Conical | 10 | 14 | 16 | 18 | 18 | 19 | 20 | 21 | 21 | 23 | 26 | 29 |
| Chestnut C3 ESP0–90 clicks · Conical · maker’s chart | 21 | 29 | 36 | 43 | 44 | 45 | 46 | 47 | 47 | 48 | 55 | 74 |
| Chestnut C3 ESP Pro0–90 clicks · Conical · maker’s chart | 21 | 29 | 36 | 43 | 44 | 45 | 46 | 47 | 47 | 48 | 55 | 74 |
| Chestnut C3 Max0–36 clicks · Conical | 9 | 12 | 13 | 15 | 15 | 16 | 17 | 17 | 18 | 19 | 22 | 25 |
| Chestnut C3 Max Pro0–36 clicks · Conical · maker’s chart | 8 | 11 | 13 | 15 | 15 | 15 | 16 | 16 | 16 | 17 | 19 | 23 |
| Chestnut C3 Pro0–36 clicks · Conical · maker’s chart | 8 | 11 | 13 | 15 | 15 | 15 | 16 | 16 | 16 | 17 | 19 | 23 |
| Chestnut C3S Pro0–36 clicks · Conical | 9 | 12 | 13 | 15 | 15 | 16 | 17 | 17 | 18 | 19 | 22 | 25 |
| Chestnut C5 ESP Pro0–150 clicks · Conical | 40 | 55 | 61 | 67 | 70 | 73 | 76 | 78 | 80 | 87 | 102 | 113 |
| Chestnut C5 Pro0–48 clicks · Conical | 17 | 23 | 26 | 28 | 30 | 31 | 32 | 33 | 34 | 37 | 43 | 46 |
| Chestnut G10–28 clicks · Conical | 9 | 12 | 14 | 16 | 16 | 17 | 18 | 18 | 19 | 20 | 23 | 26 |
| Chestnut G1 Plus0–28 clicks · Conical | 9 | 12 | 14 | 16 | 16 | 17 | 18 | 18 | 19 | 20 | 23 | 26 |
| Chestnut Nano0–30 clicks · Conical · maker’s chart | 12 | 18 | 20 | 21 | 22 | 22 | 22 | 23 | 23 | 24 | 26 | 28 |
| Chestnut S30–90 clicks · Conical | 9 | 17 | 34 | 57 | 62 | 66 | 69 | 71 | 73 | 77 | 85 | 89 |
| Chestnut Slim0–30 clicks · Conical | 10 | 14 | 16 | 18 | 18 | 19 | 20 | 21 | 21 | 23 | 26 | 29 |
| Chestnut X0–24 clicks · Conical · maker’s chart | 6 | 9 | 11 | 15 | 15 | 16 | 16 | 17 | 17 | 18 | 20 | 22 |
| Millab E010–59 clicks · Conical | 10 | 20 | 25 | 29 | 31 | 33 | 35 | 37 | 38 | 43 | 52 | 56 |
| Millab M010–10 · Conical · maker’s chart | 0.9 | 2 | 4.1 | 6.9 | 7.5 | 7.8 | 8.1 | 8.2 | 8.4 | 8.7 | 8.9 | 8.9 |
| Sculptor 0640–16 · Flat | 0.7 | 2 | 2.6 | 3.4 | 4 | 4.8 | 5.5 | 6 | 6.5 | 8 | 11.3 | 14 |
| Sculptor 064S0–16 · Flat · maker’s chart | 2.5 | 4 | 6.8 | 10.3 | 11.1 | 11.5 | 11.8 | 12.1 | 12.3 | 13 | 14.5 | 14.9 |
| Sculptor 0780–18 · Flat | 1 | 2.5 | 3 | 4 | 4.5 | 5.5 | 6 | 6.5 | 7 | 9 | 12.5 | 15.5 |
| Sculptor 078S0–18 · Flat | 1.7 | 4 | 4.8 | 5.7 | 6.2 | 6.7 | 7.2 | 7.5 | 7.8 | 8.8 | 10.9 | 12.6 |
| Turin | ||||||||||||
| CF64V0–90 · Flat | 23.7 | 39.2 | 44.6 | 51.6 | 54.9 | 58.1 | 61.3 | 63.5 | 65.7 | 72.1 | 85.4 | 88 |
| DF540–90 · Flat · maker’s chart | 17.7 | 35.1 | 35 | 59.8 | 62.9 | 64.4 | 65.9 | 66.9 | 67.9 | 70.9 | 77.8 | 84.8 |
| DF64E V20–60 · Flat | 8 | 14 | 19.6 | 26.9 | 28.7 | 29.8 | 30.9 | 31.7 | 32.4 | 34.6 | 39.7 | 45.6 |
| DF64V0–90 · Flat · maker’s chart | 20.2 | 34.1 | 41 | 49.9 | 52.7 | 54.9 | 57 | 58.5 | 59.9 | 64.2 | 73.9 | 83.1 |
| DF83 V20–90 · Flat | 22 | 40 | 42 | 44.6 | 47.1 | 50.2 | 53.3 | 55.3 | 57.4 | 63.6 | 76.9 | 83.8 |
| DF83V0–90 · Flat | 17.5 | 28.7 | 32.6 | 37.6 | 40 | 42.3 | 44.6 | 46.2 | 47.8 | 52.4 | 62.8 | 70.8 |
| SD40 V11–19 · Flat | 5.8 | 8.3 | 9.2 | 10.3 | 10.9 | 11.4 | 11.9 | 12.3 | 12.6 | 13.7 | 16 | 17.7 |
| SD40 V21–19 · Flat | 5.8 | 8.3 | 9.2 | 10.3 | 10.9 | 11.4 | 11.9 | 12.3 | 12.6 | 13.7 | 16 | 17.7 |
| VSSL | ||||||||||||
| Java0–50 clicks · Conical | 1 | 4 | 6 | 8 | 10 | 11 | 12 | 13 | 14 | 17 | 23 | 27 |
| Varia | ||||||||||||
| Evo Hybrid0–140 clicks · Conical | 41 | 65 | 76 | 85 | 90 | 96 | 102 | 107 | 111 | 125 | 140 | 140 |
| Hand Grinder0–83 clicks · Conical | 20 | 27 | 30 | 32 | 34 | 35 | 37 | 38 | 39 | 43 | 50 | 55 |
| VS3 (2nd Gen)0–19 · Conical · maker’s chart | 2.1 | 4.5 | 6.6 | 9 | 9.6 | 10 | 10.4 | 10.6 | 10.9 | 11.5 | 13.4 | 16.5 |
| VS3 (Gen 1)0–19.6 · Conical | 2.6 | 4.5 | 5.4 | 6.1 | 6.5 | 6.9 | 7.3 | 7.6 | 7.9 | 8.8 | 10.7 | 12.2 |
| VS60–24 · Flat · maker’s chart | 3.5 | 6 | 7.1 | 8.5 | 8.9 | 9.2 | 9.5 | 9.7 | 9.9 | 10.4 | 12.2 | 16.9 |
| Vevok | ||||||||||||
| Chef 061–6 · Conical | 1.1 | 1.2 | 1.4 | 1.7 | 1.9 | 2 | 2.2 | 2.3 | 2.4 | 2.8 | 3.5 | 4 |
| Chef 06 Slim1–6 · Conical | 1.1 | 1.2 | 1.4 | 1.7 | 1.9 | 2 | 2.2 | 2.3 | 2.4 | 2.8 | 3.5 | 4 |
| Wacaco | ||||||||||||
| Exagrind0–60 clicks · Conical | 14 | 24 | 27 | 29 | 31 | 33 | 35 | 36 | 37 | 42 | 51 | 57 |
| Weber | ||||||||||||
| EG-1Stepless · Flat | No single setting holds across units. How to dial it in instead | |||||||||||
| KeyStepless · Conical | No single setting holds across units. How to dial it in instead | |||||||||||
| Wilfa | ||||||||||||
| Balance1–31 · Conical · maker’s chart | 1.6 | 3.6 | 8.9 | 16.8 | 18.5 | 19.5 | 20.5 | 21 | 21.6 | 22.9 | 24.8 | 25.4 |
| Svart1–18 · Conical | 2.1 | 4.1 | 5.1 | 6.2 | 6.8 | 7.3 | 7.9 | 8.3 | 8.7 | 9.9 | 12.5 | 14.5 |
| Svart Aroma1–18 · Conical | 2.3 | 4.5 | 5.2 | 5.8 | 6.3 | 6.8 | 7.5 | 7.9 | 8.4 | 10 | 13.4 | 16.1 |
| Uniform1–41 · Flat · maker’s chart | 3 | 6 | 15 | 27 | 28 | 29 | 29 | 29 | 29 | 29 | 30 | 33 |
| Zwilling | ||||||||||||
| Enfinigy Coffee Grinder0–140 · Conical | 17.9 | 38.7 | 47.8 | 55.4 | 59.8 | 63.8 | 68.2 | 71.4 | 74.6 | 84.5 | 104.9 | 120.7 |
| montwave | ||||||||||||
| GU20–28 clicks | 6 | 9 | 10 | 11 | 11 | 12 | 13 | 13 | 13 | 15 | 17 | 19 |
| xBloom | ||||||||||||
| Studio0–80 · Conical | 14.1 | 25.3 | 30.2 | 34.3 | 36.7 | 38.9 | 41.3 | 42.9 | 44.7 | 50.1 | 61.1 | 69.6 |
Each number is the starting point. Every grinder’s page has the range to adjust in, by taste, for each method.Maker’s chart: the settings are the maker’s own published ones; the rest are estimated by comparison. If your grinder reads differently, tell us on its page.

How to read it
The numbers are positions on each grinder’s own dial: clicks from fully closed, a dial number, or rotations plus positions, as the line under each grinder’s name says. The same number on two grinders is not the same grind. To move a recipe from one grinder to another, use the grind converter.
Each grinder’s settings come from five reference points on its dial (espresso, moka, filter, French press and coarse) and a curve between them, so the methods in between land where that particular dial puts them. How the reference points are set is on the About page. For rows marked maker’s chart, the curve runs through the maker’s own settings and each page links the document; the rest are estimated by comparison with those.
Why grind charts disagree
Look up one grinder on three sites and you can get three numbers. Most of the gap is the zero point: some charts count from the burrs touching, some from the maker’s factory mark, and some grinders let owners reset zero, so two units of the same model can read differently for the same grind. The rest is the scale: a chart drawn on one generic scale has to squeeze every grinder onto it, and a dial that isn’t linear ends up wrong at the ends.
So treat any chart, this one included, as a starting point, then adjust by taste. Where we have been wrong, the fix is logged in the corrections log.
Use this chart
Link to this page or to a grinder’s own page. Grinder not listed? Tell us which one. Still choosing a grinder? Find one that fits how you brew.