Skip to main content
BrewMarkBREWMARK

Compak · Dial-in chart

Compak K3 Touch grind settings

On the Compak K3 Touch, start pour over at 8.3, espresso at 1.8 and French press at 16.7. Every other method, with the range to adjust in, is below.

Compak K3 Touch
Dial range0 – 30
ScaleNumbered dial
BurrsFlat
Filter reference8.6

The shape of this dial

The top line is the universal grind index every BrewMark recipe uses. The bottom line is the K3 Touch’s own dial. The connectors show how one maps onto the other.

FINECOARSEGRIND INDEX 0–100030COMPAK K3 TOUCH DIALEspressoV60French pressCold brew
Where the lines bunch, the dial is compressed — small moves count for more

K3 Touch grind size chart, by brew method

Start at the recommended setting, brew, then move within the range by taste. Sour or weak means go finer; bitter or harsh means go coarser.

Compak K3 Touch grind settings for espresso, moka pot, AeroPress, pour over, drip, Chemex, French press and cold brew
MethodSettingRange
EspressoFine. Aim for a 25–30s shot and adjust from there.1.8estimated0 – 4.2
Moka potFiner than filter, coarser than espresso. No tamping.5.3estimated4.2 – 6
AeroPress (short steep)For 1–2 minute recipes. Go coarser for longer steeps.6.6estimated6 – 7.5
Pour over — V60 / coneThe reference point for most published pour-over recipes.8.3estimated7.7 – 9.9
SiphonMedium. Short contact over steady heat, so start here and taste.9.1estimated8.1 – 10.9
Pour over — flat bottomKalita, Orea and similar. Slightly coarser than a cone.9.9estimated8.6 – 11.7
Steep and release — Clever / SwitchSteep, then drain through a paper filter. If it drains slowly, go coarser.10.7estimated9.1 – 12.5
Drip / batch brewAutomatic brewers. Coarser to suit the longer contact time.11.2estimated9.9 – 13.3
CuppingMedium-coarse, for tasting side by side. Keep it the same across every bowl.11.7estimated10.2 – 13.3
ChemexThe thick filter needs a coarser grind to avoid stalling.13.3estimated11.7 – 15.4
French pressCoarse. Too fine here is the usual cause of a muddy cup.16.7estimated15.1 – 18.1
Cold brewCoarsest setting you have. 12–18 hours of contact.19.4estimated18.1 – 21.4

Compak doesn’t publish a brew-method chart we could find, so these are estimated from comparable grinders. If your K3 Touch reads differently, tell us.

Every grinder on one grind size chart →
Compak K3 Touch grind size chart: espresso 1.8, V60 pour over 8.3, French press 16.7, and 9 more brew methods.
The Compak K3 Touch grind size chart as an image: every method, its setting and range, and where each sits on the dial. Download the chart (PNG).

How much room you have to adjust

Espresso → filter8.6numbers of adjustment across the fine half of the dial
Filter → coarse12.8numbers covering filter through to cold brew
Curvelinearflat burrs, interpolated linearly

That is the resolution you actually have to work with on the K3 Touch. Where the number is small, a single step moves the cup more than you would expect — so change one at a time and taste before moving again.

Coming from another grinder?

Convert a grind setting to the K3 Touch

If a recipe quotes a setting for a different grinder, this maps it onto the K3 Touch’s dial using the same curve the chart above is built from.

Converting between two grinders that are not this one? Open the full converter.

Owners’ particle-size readings

No readings for the K3 Touch yet. If you own one, you can measure your grind with a phone photo; readings are reviewed, then shown here.

How these numbers were worked out

Every grinder gets mapped onto a shared 0–100 grind index, where 0 is espresso-fine and 100 is the coarsest useful setting. Five reference points on the K3 Touch are placed on that scale — espresso, moka, filter, French press and coarse — and the settings in between are interpolated.

The K3 Touch joined the catalog in October 2026. Compak doesn’t publish a brew-method chart for it that we could find, so its reference points are estimated by comparison with grinders whose makers do. Same 58mm K3 burr/adjuster; HCG data identical to K3 Push. We couldn’t confirm whether these numbers are printed on the grinder or counted from where the burrs touch, so check your own dial before relying on the ends of the range. They are a starting point rather than a specification; if your K3 Touch reads differently, tell us.

The K3 Touch’s dial is interpolated linearly between those reference points, which is the right model for its burr geometry.

The result is that “medium-fine” resolves to a real number on this grinder rather than a vague instruction. It is a starting point, not a guarantee — burr wear, bean density and roast level all move the target, which is why every row above gives a range as well as a number.

Own a K3 Touch? Tell us your setting

If you’ve dialled in a method on your own K3 Touch, the number you landed on is the best evidence there is. Readings are checked by hand before anything changes here.

← All grinder charts