Skip to main content
BrewMarkBREWMARK

Wilfa · Dial-in chart

Wilfa Uniform grind settings

On the Wilfa Uniform, start pour over at 27, espresso at 3 and French press at 30. Every other method, with the range to adjust in, is below.

Wilfa Uniform
Dial range1 – 41
ScaleNumbered dial
BurrsFlat
Filter reference28.4

The shape of this dial

The top line is the universal grind index every BrewMark recipe uses. The bottom line is the Uniform’s own dial. The connectors show how one maps onto the other.

FINECOARSEGRIND INDEX 0–100141WILFA UNIFORM DIALEspressoV60French pressCold brew
Where the lines bunch, the dial is compressed — small moves count for more

Uniform grind size chart, by brew method

Start at the recommended setting, brew, then move within the range by taste. Sour or weak means go finer; bitter or harsh means go coarser. New to the Uniform? Start here.

Wilfa Uniform grind settings for espresso, moka pot, AeroPress, pour over, drip, Chemex, French press and cold brew
MethodSettingRange
EspressoFine. Aim for a 25–30s shot and adjust from there.First recipe →3maker’s chart1 – 4
Moka potFiner than filter, coarser than espresso. No tamping.Recipe →6estimated5 – 11
AeroPress (short steep)For 1–2 minute recipes. Go coarser for longer steeps.Recipe →15estimated11 – 21
Pour over — V60 / coneThe reference point for most published pour-over recipes.First recipe →27maker’s chart26 – 28
SiphonMedium. Short contact over steady heat, so start here and taste.28estimated25 – 29
Pour over — flat bottomKalita, Orea and similar. Slightly coarser than a cone.Recipe →29estimated28 – 29
Steep and release — Clever / SwitchSteep, then drain through a paper filter. If it drains slowly, go coarser.Recipe →29estimated28 – 29
Drip / batch brewAutomatic brewers. Coarser to suit the longer contact time.First recipe →29estimated29
CuppingMedium-coarse, for tasting side by side. Keep it the same across every bowl.29estimated29
ChemexThe thick filter needs a coarser grind to avoid stalling.Recipe →29estimated29
French pressCoarse. Too fine here is the usual cause of a muddy cup.First recipe →30maker’s chart28 – 31
Cold brewCoarsest setting you have. 12–18 hours of contact.Recipe →33estimated31 – 36

Maker’s chart settings are Wilfa’s own, from Wilfa Uniform WSFBS-100B / WSFB-100S manual (DE section p.7 table). Estimated ones sit on the same dial curve, fitted through the maker’s. Own one? Tell us the setting you use.

Every grinder on one grind size chart →
Wilfa Uniform grind size chart: espresso 3, V60 pour over 27, French press 30, and 9 more brew methods.
The Wilfa Uniform grind size chart as an image: every method, its setting and range, and where each sits on the dial. Download the chart (PNG).

Not yours yet?Buy it if you brew pour-over, AeroPress or press pot and want a very even, quiet single-dose grind, and you do not need fine espresso adjustment. The Uniform buying guide →

New to this grinder?

Your first cup on the Uniform

  1. 01

    Read the dial

    Settings are the numbers printed on the dial, and it clicks from one to the next with nothing in between.

  2. 02

    Set the starting point

    Find your brew method in the chart above and set its number. For pour over on the Uniform, that is 27.

  3. 03

    Brew, then taste

    Sour or thin means the grind is too coarse: go finer, to a lower number. Bitter or harsh means too fine: go coarser, to a higher number. More on fixing sour and bitter coffee.

  4. 04

    Change one thing at a time

    Make one small change to the grind and brew again, keeping the coffee, dose and water the same. The range beside each method is how far to go before something else is the problem.

Words on this pageGrind size · Flat burrs · Grind index · Extraction · Dialing in

Goes with your Uniform

What makes these settings work

A setting only repeats if the dose and the pour do too. Picked for how this grinder is used, not ranked, and nothing here is sponsored. Each one links to the guide that explains it.

How it compares

The Uniform against the electric grinders from $194 to $449:

  • Joint longest warranty of the 13 with a published figure: 5 years.

From each maker’s published specs (the Uniform’s); a grinder whose maker doesn’t state a figure is left out of that line. Not a test or a score.

Can the Wilfa Uniform grind for espresso?

Yes, with limits. The Uniform reaches espresso fineness, but its steps are coarse there, so one click can move a shot a long way. It suits a pressurized (dual-wall) basket, or the odd shot, better than dialing in a standard basket every day. Start at 3 and adjust by taste.

BrewMark’s rating, from the maker’s specs and published reviews listed in the buying guide. We haven’t tested it.

The best espresso grinders under $500 →

How much room you have to adjust

Espresso → filter27.4numbers of adjustment across the fine half of the dial
Filter → coarse7.6numbers covering filter through to cold brew
Curvelinearflat burrs, interpolated linearly

That is the resolution you actually have to work with on the Uniform. Where the number is small, a single step moves the cup more than you would expect — so change one at a time and taste before moving again.

Dialing in the Uniform

Designed with Tim Wendelboe for filter coffee, and honest about it. Forty-one settings across a wide range, flat burrs, and a grind that is genuinely clean in the brew band it was built for. It does reach espresso fineness — but the step size is the problem rather than the range: reviewers report landing between settings, where one step chokes the basket and the next runs fast, with only a narrow window in between. Treat occasional espresso as possible with technique rather than as something the grinder is for. For pour over, which is the job, it is one of the better flat-burr options at the price.

Coming from another grinder?

Convert a grind setting to the Uniform

If a recipe quotes a setting for a different grinder, this maps it onto the Uniform’s dial using the same curve the chart above is built from.

Converting between two grinders that are not this one? Open the full converter.

Owners’ particle-size readings

No readings for the Uniform yet. If you own one, you can measure your grind with a phone photo; readings are reviewed, then shown here.

How these numbers were worked out

Every grinder gets mapped onto a shared 0–100 grind index, where 0 is espresso-fine and 100 is the coarsest useful setting. Five reference points on the Uniform are placed on that scale — espresso, moka, filter, French press and coarse — and the settings in between are interpolated.

Wilfa publishes its own brew-method chart for the Uniform, and we checked every number against it. The chart above prints Wilfa’s settings for the methods it names, and the reference points are fitted so the curve follows them; the other methods, and every conversion to and from this grinder, are read off that curve. Source: Wilfa Uniform WSFBS-100B / WSFB-100S manual (DE section p.7 table).

The Uniform’s dial is interpolated linearly between those reference points, which is the right model for its burr geometry.

The result is that “medium-fine” resolves to a real number on this grinder rather than a vague instruction. It is a starting point, not a guarantee — burr wear, bean density and roast level all move the target, which is why every row above gives a range as well as a number.

Corrections to this page

  • 2026-10-23For every grinder whose maker publishes a brew-method chart, the chart now prints the maker’s own settings for the methods it names, checked against the maker’s document, and the rest follow a dial curve fitted through them. Per-setting micron figures are gone; particle sizes are given only for espresso, drip and cupping, where independent sources agree.
Every correction, with what the page said before →

Own a Uniform? Tell us your setting

If you’ve dialled in a method on your own Uniform, the number you landed on is the best evidence there is. Readings are checked by hand before anything changes here.

← All grinder charts