Fiorenzato · Dial-in chart
Fiorenzato Allground Sense grind settings
On the Fiorenzato Allground Sense, start pour over at 51.4, espresso at 23.9 and French press at 73. Every other method, with the range to adjust in, is below.
The shape of this dial
The top line is the universal grind index every BrewMark recipe uses. The bottom line is the Allground Sense’s own dial. The connectors show how one maps onto the other.
Allground Sense settings for each brew method
Start at the recommended setting, brew, then move within the range by taste. Sour or weak means go finer; bitter or harsh means go coarser.
| Method | Setting | Range |
|---|---|---|
| TurkishNear the fine end of this dial. Turkish wants powder, around 150 µm. | 2.4≈ 150 µm | fine end |
| EspressoFine. Aim for a 25–30s shot and adjust from there. | 23.9≈ 330 µm | 16.3 – 34.6 |
| Moka potFiner than filter, coarser than espresso. No tamping. | 39.2≈ 450 µm | 34.6 – 41.9 |
| AeroPress (short steep)For 1–2 minute recipes. Go coarser for longer steeps. | 44.5≈ 500 µm | 41.9 – 48.2 |
| Pour over — V60 / coneThe reference point for most published pour-over recipes. | 51.4≈ 560 µm | 48.8 – 55.9 |
| SiphonMedium. Short contact over steady heat, so start here and taste. | 53.9≈ 580 µm | 50.4 – 58.7 |
| Pour over — flat bottomKalita, Orea and similar. Slightly coarser than a cone. | 55.9≈ 590 µm | 52.5 – 60.7 |
| Steep and release — Clever / SwitchSteep, then drain through a paper filter. If it drains slowly, go coarser. | 58≈ 610 µm | 53.9 – 62.8 |
| Drip / batch brewAutomatic brewers. Coarser to suit the longer contact time. | 59.3≈ 620 µm | 55.9 – 64.8 |
| CuppingMedium-coarse, for tasting side by side. Keep it the same across every bowl. | 60.7≈ 630 µm | 56.6 – 64.8 |
| ChemexThe thick filter needs a coarser grind to avoid stalling. | 64.8≈ 670 µm | 60.7 – 70.3 |
| French pressCoarse. Too fine here is the usual cause of a muddy cup. | 73≈ 740 µm | 69.6 – 73 |
| Cold brewCoarsest setting you have. 12–18 hours of contact. | 73≈ 740 µm | at dial limit |
≈ µm is the particle size, approximate, after Honest Coffee Guide’s scale for the Allground Sense. It is not the maker’s microns per click, which measure how far the burrs move.
How much room you have to adjust
That is the resolution you actually have to work with on the Allground Sense. Where the number is small, a single step moves the cup more than you would expect — so change one at a time and taste before moving again.
Cold brew sits at the end of the Allground Sense’s travel — you can reach it, but there is no room left to adjust further in that direction.
Coming from another grinder?
Convert a grind setting to the Allground Sense
If a recipe quotes a setting for a different grinder, this maps it onto the Allground Sense’s dial using the same curve the chart above is built from.
Converting between two grinders that are not this one? Open the full converter.
How these numbers were worked out
Every grinder gets mapped onto a shared 0–100 grind index, where 0 is espresso-fine and 100 is the coarsest useful setting. Five reference points on the Allground Sense are placed on that scale — espresso, moka, filter, French press and coarse — and the settings in between are interpolated.
The Allground Sense joined the catalog in October 2026. Its reference points were worked out rather than read off a maker’s chart: Honest Coffee Guide places every setting on this grinder on one scale of particle size, and each point sits where that scale reaches the size the same method lands on across the grinders we have checked. These numbers are counted the way Honest Coffee Guide counts them (number of dots), not read off a scale printed on the grinder, so count from where the burrs just touch; the dial may run further than this chart. That makes them a starting point rather than a specification, and they are marked unverified until a manufacturer’s chart confirms them. Sources: Honest Coffee Guide.
The Allground Sense’s dial is interpolated linearly between those reference points, which is the right model for its burr geometry.
The result is that “medium-fine” resolves to a real number on this grinder rather than a vague instruction. It is a starting point, not a guarantee — burr wear, bean density and roast level all move the target, which is why every row above gives a range as well as a number.
Free wall chart
Put the Allground Sense numbers next to the grinder
The main methods on one sheet, laid out on the Allground Sense’s own dial so you can see where the settings bunch up. Print it, pin it, stop reaching for your phone with wet hands.
Or have the Allground Sense chart emailed
The same settings, sent once, for when you are standing at the grinder and nowhere near a printer.
One email with the chart. Nothing else unless you ask.
Make these numbers yours
This chart is the same for every Allground Sense in the world. Log what you actually brewed and it stops being — the app remembers the setting that worked for your beans and shifts the starting point toward it. Free on iOS.
Get the iOS appGrinders that dial in like this one
Similar burrs, scale or dial range — which means settings translate between them more predictably than across the whole catalog.
Own a Allground Sense? Tell us your setting
If you’ve dialled in a method on your own Allground Sense, the number you landed on is the best evidence there is. Readings are checked by hand before anything changes here.