Skip to main content
BrewMarkBREWMARK

Option-O · Dial-in chart

Option-O Lagom Mini grind settings

On the Option-O Lagom Mini, start pour over at 21.2, espresso at 6.3 and French press at 32.7. Every other method, with the range to adjust in, is below.

Option-O Lagom Mini
Dial range0 – 50
ScaleNumbered dial
BurrsConical
Filter reference22

The shape of this dial

The top line is the universal grind index every BrewMark recipe uses. The bottom line is the Lagom Mini’s own dial. The connectors show how one maps onto the other.

FINECOARSEGRIND INDEX 0–100050OPTION-O LAGOM MINI DIALEspressoV60French pressCold brew
Where the lines bunch, the dial is compressed — small moves count for more

Lagom Mini grind size chart, by brew method

Start at the recommended setting, brew, then move within the range by taste. Sour or weak means go finer; bitter or harsh means go coarser. New to the Lagom Mini? Start here.

Option-O Lagom Mini grind settings for espresso, moka pot, AeroPress, pour over, drip, Chemex, French press and cold brew
MethodSettingRange
EspressoFine. Aim for a 25–30s shot and adjust from there.First recipe →6.3estimated4 – 9.6
Moka potFiner than filter, coarser than espresso. No tamping.Recipe →11estimated9.6 – 13.3
AeroPress (short steep)For 1–2 minute recipes. Go coarser for longer steeps.Recipe →15.6estimated13.3 – 18.7
Pour over — V60 / coneThe reference point for most published pour-over recipes.First recipe →21.2estimated19.1 – 23.9
SiphonMedium. Short contact over steady heat, so start here and taste.22.8estimated20.4 – 25.2
Pour over — flat bottomKalita, Orea and similar. Slightly coarser than a cone.Recipe →23.9estimated22 – 26.2
Steep and release — Clever / SwitchSteep, then drain through a paper filter. If it drains slowly, go coarser.Recipe →24.9estimated22.8 – 27.2
Drip / batch brewAutomatic brewers. Coarser to suit the longer contact time.First recipe →25.6estimated23.9 – 28.2
CuppingMedium-coarse, for tasting side by side. Keep it the same across every bowl.26.2estimated24.2 – 28.2
ChemexThe thick filter needs a coarser grind to avoid stalling.Recipe →28.2estimated26.2 – 30.7
French pressCoarse. Too fine here is the usual cause of a muddy cup.First recipe →32.7estimated30.4 – 35.3
Cold brewCoarsest setting you have. 12–18 hours of contact.Recipe →38estimated35.3 – 42

Option-O doesn’t publish a brew-method chart we could find, so these are estimated from comparable grinders. If your Lagom Mini reads differently, tell us.

Every grinder on one grind size chart →
Option-O Lagom Mini grind size chart: espresso 6.3, V60 pour over 21.2, French press 32.7, and 9 more brew methods.
The Option-O Lagom Mini grind size chart as an image: every method, its setting and range, and where each sits on the dial. Download the chart (PNG).

Not yours yet?Worth buying used if you brew one or two cups a day, want electric grinding in a hand-grinder footprint, and do not mind slow espresso grinding. The Lagom Mini buying guide →

New to this grinder?

Your first cup on the Lagom Mini

  1. 01

    Read the dial

    Settings are the numbers printed on the dial. It is stepless, so any point between two numbers is a setting too.

  2. 02

    Set the starting point

    Find your brew method in the chart above and set its number. For pour over on the Lagom Mini, that is 21.2.

  3. 03

    Brew, then taste

    Sour or thin means the grind is too coarse: go finer, to a lower number. Bitter or harsh means too fine: go coarser, to a higher number. More on fixing sour and bitter coffee.

  4. 04

    Change one thing at a time

    Make one small change to the grind and brew again, keeping the coffee, dose and water the same. The range beside each method is how far to go before something else is the problem.

Words on this pageGrind size · Conical burrs · Grind index · Extraction · Dialing in

Goes with your Lagom Mini

What makes these settings work

A setting only repeats if the dose and the pour do too. Picked for how this grinder is used, not ranked, and nothing here is sponsored. Each one links to the guide that explains it.

How much room you have to adjust

Espresso → filter18numbers of adjustment across the fine half of the dial
Filter → coarse20numbers covering filter through to cold brew
Curvesplineconical burrs, fitted with a monotone curve

That is the resolution you actually have to work with on the Lagom Mini. Where the number is small, a single step moves the cup more than you would expect — so change one at a time and taste before moving again.

Dialing in the Lagom Mini

A compact single-dose grinder designed around burr swapping, so its character depends heavily on which set is fitted. Stepless. Low retention is the main reason to own it — it is built for people who change coffees constantly.

Coming from another grinder?

Convert a grind setting to the Lagom Mini

If a recipe quotes a setting for a different grinder, this maps it onto the Lagom Mini’s dial using the same curve the chart above is built from.

Converting between two grinders that are not this one? Open the full converter.

Owners’ particle-size readings

No readings for the Lagom Mini yet. If you own one, you can measure your grind with a phone photo; readings are reviewed, then shown here.

How these numbers were worked out

Every grinder gets mapped onto a shared 0–100 grind index, where 0 is espresso-fine and 100 is the coarsest useful setting. Five reference points on the Lagom Mini are placed on that scale — espresso, moka, filter, French press and coarse — and the settings in between are interpolated.

Option-O doesn’t publish a brew-method chart for the Lagom Mini that we could find, so its reference points are estimated by comparison with grinders whose makers do. The moka and French press points in particular were interpolated from the pattern the rest of the catalog shows rather than read off a chart for this grinder. They are a starting point rather than a specification; if your Lagom Mini reads differently, tell us.

Because the Lagom Mini uses conical burrs, the curve between those points is fitted with a monotone cubic spline rather than straight lines. Conical burr dials are rarely linear, and the spline guarantees the curve never doubles back — a coarser index always produces a coarser setting.

The result is that “medium-fine” resolves to a real number on this grinder rather than a vague instruction. It is a starting point, not a guarantee — burr wear, bean density and roast level all move the target, which is why every row above gives a range as well as a number.

Corrections to this page

  • 2026-10-21VS3 and Lagom Mini are conical (48 mm, per their makers); the DBM-8 is flat.
Every correction, with what the page said before →

Own a Lagom Mini? Tell us your setting

If you’ve dialled in a method on your own Lagom Mini, the number you landed on is the best evidence there is. Readings are checked by hand before anything changes here.

← All grinder charts