Skip to main content
BrewMarkBREWMARK

Niche · Dial-in chart

Niche Zero grind settings

On the Niche Zero, start pour over at 40, espresso at 12.8 and French press at 47.5. Every other method, with the range to adjust in, is below.

Niche Zero
Dial range0 – 50
ScaleNumbered dial
BurrsConical
Filter reference40.9

The shape of this dial

The top line is the universal grind index every BrewMark recipe uses. The bottom line is the Zero’s own dial. The connectors show how one maps onto the other.

FINECOARSEGRIND INDEX 0–100050NICHE ZERO DIALEspressoV60French pressCold brew
Where the lines bunch, the dial is compressed — small moves count for more

Zero grind size chart, by brew method

Start at the recommended setting, brew, then move within the range by taste. Sour or weak means go finer; bitter or harsh means go coarser. New to the Zero? Start here.

Niche Zero grind settings for espresso, moka pot, AeroPress, pour over, drip, Chemex, French press and cold brew
MethodSettingRange
EspressoFine. Aim for a 25–30s shot and adjust from there.First recipe →12.8maker’s chart5 – 20
Moka potFiner than filter, coarser than espresso. No tamping.Recipe →24.7maker’s chart20 – 30
AeroPress (short steep)For 1–2 minute recipes. Go coarser for longer steeps.Recipe →32.7maker’s chart30 – 35
Pour over — V60 / coneThe reference point for most published pour-over recipes.First recipe →40maker’s chart35 – 45
SiphonMedium. Short contact over steady heat, so start here and taste.41.7estimated39.1 – 43.9
Pour over — flat bottomKalita, Orea and similar. Slightly coarser than a cone.Recipe →42.8estimated40.9 – 44.5
Steep and release — Clever / SwitchSteep, then drain through a paper filter. If it drains slowly, go coarser.Recipe →43.6estimated41.7 – 45.1
Drip / batch brewAutomatic brewers. Coarser to suit the longer contact time.First recipe →44.1estimated42.8 – 45.6
CuppingMedium-coarse, for tasting side by side. Keep it the same across every bowl.44.5estimated43.1 – 45.6
ChemexThe thick filter needs a coarser grind to avoid stalling.Recipe →45.6estimated44.5 – 46.6
French pressCoarse. Too fine here is the usual cause of a muddy cup.First recipe →47.5maker’s chart45 – 50
Cold brewCoarsest setting you have. 12–18 hours of contact.Recipe →49estimated48.4 – 50

Maker’s chart settings are Niche’s own, from The ultimate grind size guide for Niche grinders (Niche blog). Estimated ones sit on the same dial curve, fitted through the maker’s. Own one? Tell us the setting you use.

Every grinder on one grind size chart →
Niche Zero grind size chart: espresso 12.8, V60 pour over 40, French press 47.5, and 9 more brew methods.
The Niche Zero grind size chart as an image: every method, its setting and range, and where each sits on the dial. Download the chart (PNG).

Not yours yet?Buy it if you single-dose espresso, want a quiet and tidy workflow, and like a classic, full-bodied shot; flat-burr clarity seekers should look elsewhere. The Zero buying guide →

New to this grinder?

Your first cup on the Zero

  1. 01

    Read the dial

    Settings are the numbers printed on the dial. It is stepless, so any point between two numbers is a setting too.

  2. 02

    Set the starting point

    Find your brew method in the chart above and set its number. For pour over on the Zero, that is 40.

  3. 03

    Brew, then taste

    Sour or thin means the grind is too coarse: go finer, to a lower number. Bitter or harsh means too fine: go coarser, to a higher number. More on fixing sour and bitter coffee.

  4. 04

    Change one thing at a time

    Make one small change to the grind and brew again, keeping the coffee, dose and water the same. The range beside each method is how far to go before something else is the problem.

Words on this pageGrind size · Conical burrs · Grind index · Extraction · Dialing in

Goes with your Zero

What makes these settings work

A setting only repeats if the dose and the pour do too. Picked for how this grinder is used, not ranked, and nothing here is sponsored. Each one links to the guide that explains it.

Can the Niche Zero grind for espresso?

Yes. The Zero adjusts in steps fine enough to dial in a shot on a standard single-wall basket, which is what most espresso recipes assume. Start at 12.8 and adjust by taste.

BrewMark’s rating, from the maker’s specs and published reviews listed in the buying guide. We haven’t tested it.

How much room you have to adjust

Espresso → filter34.6numbers of adjustment across the fine half of the dial
Filter → coarse9.1numbers covering filter through to cold brew
Curvesplineconical burrs, fitted with a monotone curve

That is the resolution you actually have to work with on the Zero. Where the number is small, a single step moves the cup more than you would expect — so change one at a time and taste before moving again.

Dialing in the Zero

Single-dose, stepless, and calibrated so that the same numbered setting means roughly the same thing between units — unusual, and the reason Niche numbers get quoted directly between users. Because it is stepless, the settings below are targets rather than detents: land near the number and adjust by taste. Its espresso and filter ranges overlap more than the dial implies.

Coming from another grinder?

Convert a grind setting to the Zero

If a recipe quotes a setting for a different grinder, this maps it onto the Zero’s dial using the same curve the chart above is built from.

Converting between two grinders that are not this one? Open the full converter.

Owners’ particle-size readings

No readings for the Zero yet. If you own one, you can measure your grind with a phone photo; readings are reviewed, then shown here.

How these numbers were worked out

Every grinder gets mapped onto a shared 0–100 grind index, where 0 is espresso-fine and 100 is the coarsest useful setting. Five reference points on the Zero are placed on that scale — espresso, moka, filter, French press and coarse — and the settings in between are interpolated.

Niche publishes its own brew-method chart for the Zero, and we checked every number against it. The chart above prints Niche’s settings for the methods it names, and the reference points are fitted so the curve follows them; the other methods, and every conversion to and from this grinder, are read off that curve. Source: The ultimate grind size guide for Niche grinders (Niche blog).

Because the Zero uses conical burrs, the curve between those points is fitted with a monotone cubic spline rather than straight lines. Conical burr dials are rarely linear, and the spline guarantees the curve never doubles back — a coarser index always produces a coarser setting.

The result is that “medium-fine” resolves to a real number on this grinder rather than a vague instruction. It is a starting point, not a guarantee — burr wear, bean density and roast level all move the target, which is why every row above gives a range as well as a number.

Corrections to this page

  • 2026-10-23For every grinder whose maker publishes a brew-method chart, the chart now prints the maker’s own settings for the methods it names, checked against the maker’s document, and the rest follow a dial curve fitted through them. Per-setting micron figures are gone; particle sizes are given only for espresso, drip and cupping, where independent sources agree.
  • 2026-10-22Each chart is fitted to Niche’s own grind size guide, and every method now falls inside its range. Refitted again on 2026-10-23 with the rest of the catalog: on the Zero, espresso is now about 13, V60 40 and French press 47.5; on the Duo, espresso 5, V60 37.6 and French press 47.5.
Every correction, with what the page said before →

Own a Zero? Tell us your setting

If you’ve dialled in a method on your own Zero, the number you landed on is the best evidence there is. Readings are checked by hand before anything changes here.

← All grinder charts