Timemore Sculptor 078STimemore · Dial-in chart
Timemore Sculptor 078S grind settings
On the Timemore Sculptor 078S, start pour over at 5.7, espresso at 1.7 and French press at 10.9. Every other method, with the range to adjust in, is below.

The shape of this dial
The top line is the universal grind index every BrewMark recipe uses. The bottom line is the Sculptor 078S’s own dial. The connectors show how one maps onto the other.
Sculptor 078S grind size chart, by brew method
Start at the recommended setting, brew, then move within the range by taste. Sour or weak means go finer; bitter or harsh means go coarser.
| Method | Setting | Range |
|---|---|---|
| EspressoFine. Aim for a 25–30s shot and adjust from there. | 1.7estimated | 0.5 – 3.3 |
| Moka potFiner than filter, coarser than espresso. No tamping. | 4estimated | 3.3 – 4.4 |
| AeroPress (short steep)For 1–2 minute recipes. Go coarser for longer steeps. | 4.8estimated | 4.4 – 5.3 |
| Pour over — V60 / coneThe reference point for most published pour-over recipes. | 5.7estimated | 5.4 – 6.7 |
| SiphonMedium. Short contact over steady heat, so start here and taste. | 6.2estimated | 5.6 – 7.3 |
| Pour over — flat bottomKalita, Orea and similar. Slightly coarser than a cone. | 6.7estimated | 5.9 – 7.8 |
| Steep and release — Clever / SwitchSteep, then drain through a paper filter. If it drains slowly, go coarser. | 7.2estimated | 6.2 – 8.3 |
| Drip / batch brewAutomatic brewers. Coarser to suit the longer contact time. | 7.5estimated | 6.7 – 8.8 |
| CuppingMedium-coarse, for tasting side by side. Keep it the same across every bowl. | 7.8estimated | 6.9 – 8.8 |
| ChemexThe thick filter needs a coarser grind to avoid stalling. | 8.8estimated | 7.8 – 10.1 |
| French pressCoarse. Too fine here is the usual cause of a muddy cup. | 10.9estimated | 9.9 – 11.7 |
| Cold brewCoarsest setting you have. 12–18 hours of contact. | 12.6estimated | 11.7 – 13.8 |
Timemore doesn’t publish a brew-method chart we could find, so these are estimated from comparable grinders. If your Sculptor 078S reads differently, tell us.
Every grinder on one grind size chart →
Not yours yet?Buy it if you want a quiet, low-retention single-dose grinder and enjoy tuning RPM and grind for both espresso and filter; skip it if you want plug-and-play. The Sculptor 078S buying guide →
Can the Timemore Sculptor 078S grind for espresso?
Yes. The Sculptor 078S adjusts in steps fine enough to dial in a shot on a standard single-wall basket, which is what most espresso recipes assume. Start at 1.7 and adjust by taste.
BrewMark’s rating, from the maker’s specs and published reviews listed in the buying guide. We haven’t tested it.
How much room you have to adjust
That is the resolution you actually have to work with on the Sculptor 078S. Where the number is small, a single step moves the cup more than you would expect — so change one at a time and taste before moving again.
Coming from another grinder?
Convert a grind setting to the Sculptor 078S
If a recipe quotes a setting for a different grinder, this maps it onto the Sculptor 078S’s dial using the same curve the chart above is built from.
Converting between two grinders that are not this one? Open the full converter.
Owners’ particle-size readings
No readings for the Sculptor 078S yet. If you own one, you can measure your grind with a phone photo; readings are reviewed, then shown here.
How these numbers were worked out
Every grinder gets mapped onto a shared 0–100 grind index, where 0 is espresso-fine and 100 is the coarsest useful setting. Five reference points on the Sculptor 078S are placed on that scale — espresso, moka, filter, French press and coarse — and the settings in between are interpolated.
The Sculptor 078S joined the catalog in October 2026. Timemore doesn’t publish a brew-method chart for it that we could find, so its reference points are estimated by comparison with grinders whose makers do. 078S uses espresso-capable flat burrs and a stepless dial; the 078 has turbo brew burrs and a stepped 36-setting dial. They are a starting point rather than a specification; if your Sculptor 078S reads differently, tell us.Maker’s details: timemore.com.
The Sculptor 078S’s dial is interpolated linearly between those reference points, which is the right model for its burr geometry.
The result is that “medium-fine” resolves to a real number on this grinder rather than a vague instruction. It is a starting point, not a guarantee — burr wear, bean density and roast level all move the target, which is why every row above gives a range as well as a number.
Own a Sculptor 078S? Tell us your setting
If you’ve dialled in a method on your own Sculptor 078S, the number you landed on is the best evidence there is. Readings are checked by hand before anything changes here.