Skip to main content
BrewMarkBREWMARK

Fellow · Dial-in chart

Fellow Opus grind settings

On the Fellow Opus, start pour over at 6.3, espresso at 1.2 and French press at 9. Every other method, with the range to adjust in, is below.

Fellow Opus
Dial range1 – 11
ScaleNumbered dial
BurrsConical
Filter reference7.1

The shape of this dial

The top line is the universal grind index every BrewMark recipe uses. The bottom line is the Opus’s own dial. The connectors show how one maps onto the other.

FINECOARSEGRIND INDEX 0–100111FELLOW OPUS DIALEspressoV60French pressCold brew
Where the lines bunch, the dial is compressed — small moves count for more

Opus grind size chart, by brew method

Start at the recommended setting, brew, then move within the range by taste. Sour or weak means go finer; bitter or harsh means go coarser. New to the Opus? Start here.

Fellow Opus grind settings for espresso, moka pot, AeroPress, pour over, drip, Chemex, French press and cold brew
MethodSettingRange
EspressoFine. Aim for a 25–30s shot and adjust from there.First recipe →1.2maker’s chart1 – 2
Moka potFiner than filter, coarser than espresso. No tamping.Recipe →1.3estimated1.2 – 2.2
AeroPress (short steep)For 1–2 minute recipes. Go coarser for longer steeps.Recipe →3.2maker’s chart2 – 5
Pour over — V60 / coneThe reference point for most published pour-over recipes.First recipe →6.3maker’s chart5 – 9
SiphonMedium. Short contact over steady heat, so start here and taste.7.2estimated6.2 – 8
Pour over — flat bottomKalita, Orea and similar. Slightly coarser than a cone.Recipe →7.3estimated7 – 8
Steep and release — Clever / SwitchSteep, then drain through a paper filter. If it drains slowly, go coarser.Recipe →8estimated7.2 – 8.1
Drip / batch brewAutomatic brewers. Coarser to suit the longer contact time.First recipe →8maker’s chart7 – 9
CuppingMedium-coarse, for tasting side by side. Keep it the same across every bowl.8maker’s chart7 – 9
ChemexThe thick filter needs a coarser grind to avoid stalling.Recipe →8.2estimated8 – 8.3
French pressCoarse. Too fine here is the usual cause of a muddy cup.First recipe →9maker’s chart8 – 10
Cold brewCoarsest setting you have. 12–18 hours of contact.Recipe →10maker’s chart10 – 11

Maker’s chart settings are Fellow’s own, from Meet Opus 'get-to-know-you' guide 789-00023 B (UK), p.5 'Grind settings' (bar chart). Estimated ones sit on the same dial curve, fitted through the maker’s. Own one? Tell us the setting you use.

Every grinder on one grind size chart →
Fellow Opus grind size chart: espresso 1.2, V60 pour over 6.3, French press 9, and 9 more brew methods.
The Fellow Opus grind size chart as an image: every method, its setting and range, and where each sits on the dial. Download the chart (PNG).

Not yours yet?Worth buying used if you want one quiet, compact electric grinder for filter and occasional espresso; for dedicated espresso or zero retention, look elsewhere. The Opus buying guide →

New to this grinder?

Your first cup on the Opus

  1. 01

    Read the dial

    The dial has 3 small marks between each number. A setting like 6.3 means the third mark after 6, not a decimal.

  2. 02

    Set the starting point

    Find your brew method in the chart above and set its number. For pour over on the Opus, that is 6.3.

  3. 03

    Brew, then taste

    Sour or thin means the grind is too coarse: go finer, to a lower number. Bitter or harsh means too fine: go coarser, to a higher number. More on fixing sour and bitter coffee.

  4. 04

    Change one thing at a time

    Make one small change to the grind and brew again, keeping the coffee, dose and water the same. The range beside each method is how far to go before something else is the problem.

Words on this pageGrind size · Conical burrs · Grind index · Extraction · Dialing in

Goes with your Opus

What makes these settings work

A setting only repeats if the dose and the pour do too. Picked for how this grinder is used, not ranked, and nothing here is sponsored. Each one links to the guide that explains it.

How much room you have to adjust

Espresso → filter5.7numbers of adjustment across the fine half of the dial
Filter → coarse3.9numbers covering filter through to cold brew
Curvesplineconical burrs, fitted with a monotone curve

That is the resolution you actually have to work with on the Opus. Where the number is small, a single step moves the cup more than you would expect — so change one at a time and taste before moving again.

Dialing in the Opus

Marketed as all-purpose, and it genuinely does cover more range than the Ode, but the espresso end is workable rather than good — expect to chase it. Where it earns its place is the coarse end: cold brew and French press come out notably even. If you bought the Opus mainly for espresso, dial it as a brew grinder first and judge it there.

Coming from another grinder?

Convert a grind setting to the Opus

If a recipe quotes a setting for a different grinder, this maps it onto the Opus’s dial using the same curve the chart above is built from.

Converting between two grinders that are not this one? Open the full converter.

Owners’ particle-size readings

No readings for the Opus yet. If you own one, you can measure your grind with a phone photo; readings are reviewed, then shown here.

How these numbers were worked out

Every grinder gets mapped onto a shared 0–100 grind index, where 0 is espresso-fine and 100 is the coarsest useful setting. Five reference points on the Opus are placed on that scale — espresso, moka, filter, French press and coarse — and the settings in between are interpolated.

Fellow publishes its own brew-method chart for the Opus, and we checked every number against it. The chart above prints Fellow’s settings for the methods it names, and the reference points are fitted so the curve follows them; the other methods, and every conversion to and from this grinder, are read off that curve. Source: Meet Opus 'get-to-know-you' guide 789-00023 B (UK), p.5 'Grind settings' (bar chart).

Because the Opus uses conical burrs, the curve between those points is fitted with a monotone cubic spline rather than straight lines. Conical burr dials are rarely linear, and the spline guarantees the curve never doubles back — a coarser index always produces a coarser setting.

The result is that “medium-fine” resolves to a real number on this grinder rather than a vague instruction. It is a starting point, not a guarantee — burr wear, bean density and roast level all move the target, which is why every row above gives a range as well as a number.

Corrections to this page

  • 2026-10-23For every grinder whose maker publishes a brew-method chart, the chart now prints the maker’s own settings for the methods it names, checked against the maker’s document, and the rest follow a dial curve fitted through them. Per-setting micron figures are gone; particle sizes are given only for espresso, drip and cupping, where independent sources agree.
  • 2026-10-22Written as the number and which mark after it, the way owners count them: on an Ode, 4, 4.1, 4.2, then 5; on an Opus, up to 4.3. The positions themselves did not change. A setting typed as 4.2 for these grinders is now read as the second mark.
  • 2026-09-14Rescaled to the printed 1–11 ring. The anchors are still marked unverified pending Fellow's own guide.
Every correction, with what the page said before →

Own a Opus? Tell us your setting

If you’ve dialled in a method on your own Opus, the number you landed on is the best evidence there is. Readings are checked by hand before anything changes here.

← All grinder charts