Skip to main content
BrewMarkBREWMARK

Fellow · Dial-in chart

Fellow Ode Gen 1 grind settings

On the Fellow Ode Gen 1, start pour over at 3.1, espresso at 1.1 and French press at 8. Every other method, with the range to adjust in, is below.

Fellow Ode Gen 1
Dial range1 – 11
ScaleNumbered dial
BurrsFlat
Filter reference3.6

The shape of this dial

The top line is the universal grind index every BrewMark recipe uses. The bottom line is the Ode Gen 1’s own dial. The connectors show how one maps onto the other.

FINECOARSEGRIND INDEX 0–100111FELLOW ODE GEN 1 DIALEspressoV60French pressCold brew
Where the lines bunch, the dial is compressed — small moves count for more

Ode Gen 1 grind size chart, by brew method

Start at the recommended setting, brew, then move within the range by taste. Sour or weak means go finer; bitter or harsh means go coarser. New to the Ode Gen 1? Start here.

Fellow Ode Gen 1 grind settings for espresso, moka pot, AeroPress, pour over, drip, Chemex, French press and cold brew
MethodSettingRange
EspressoFine. Aim for a 25–30s shot and adjust from there.First recipe →1.1estimated1 – 1.2
Moka potFiner than filter, coarser than espresso. No tamping.Recipe →1.2estimated1.2 – 2
AeroPress (short steep)For 1–2 minute recipes. Go coarser for longer steeps.Recipe →2.2maker’s chart1 – 4
Pour over — V60 / coneThe reference point for most published pour-over recipes.First recipe →3.1maker’s chart2 – 5
SiphonMedium. Short contact over steady heat, so start here and taste.4estimated3.1 – 5
Pour over — flat bottomKalita, Orea and similar. Slightly coarser than a cone.Recipe →4.1estimated3.2 – 5.1
Steep and release — Clever / SwitchSteep, then drain through a paper filter. If it drains slowly, go coarser.Recipe →4.2estimated4 – 5.2
Drip / batch brewAutomatic brewers. Coarser to suit the longer contact time.First recipe →5maker’s chart4 – 6
CuppingMedium-coarse, for tasting side by side. Keep it the same across every bowl.3maker’s chart2 – 3
ChemexThe thick filter needs a coarser grind to avoid stalling.Recipe →6.1estimated5.1 – 7.1
French pressCoarse. Too fine here is the usual cause of a muddy cup.First recipe →8maker’s chart6 – 10
Cold brewCoarsest setting you have. 12–18 hours of contact.Recipe →9.2maker’s chart9 – 11

Maker’s chart settings are Fellow’s own, from Ode Brew Grinder Quick Start and Brewing Guide, p.6 'Grind settings'. Estimated ones sit on the same dial curve, fitted through the maker’s. Own one? Tell us the setting you use.

Every grinder on one grind size chart →
Fellow Ode Gen 1 grind size chart: espresso 1.1, V60 pour over 3.1, French press 8, and 9 more brew methods.
The Fellow Ode Gen 1 grind size chart as an image: every method, its setting and range, and where each sits on the dial. Download the chart (PNG).

Not yours yet?Worth buying used if you brew drip, pour-over or French press and want quiet flat burrs; check which burrs are fitted, and skip it for espresso. The Ode Gen 1 buying guide →

New to this grinder?

Your first cup on the Ode Gen 1

  1. 01

    Read the dial

    The dial has 2 small marks between each number. A setting like 3.1 means the first mark after 3, not a decimal.

  2. 02

    Set the starting point

    Find your brew method in the chart above and set its number. For pour over on the Ode Gen 1, that is 3.1.

  3. 03

    Brew, then taste

    Sour or thin means the grind is too coarse: go finer, to a lower number. Bitter or harsh means too fine: go coarser, to a higher number. More on fixing sour and bitter coffee.

  4. 04

    Change one thing at a time

    Make one small change to the grind and brew again, keeping the coffee, dose and water the same. The range beside each method is how far to go before something else is the problem.

Words on this pageGrind size · Flat burrs · Grind index · Extraction · Dialing in

Goes with your Ode Gen 1

What makes these settings work

A setting only repeats if the dose and the pour do too. Picked for how this grinder is used, not ranked, and nothing here is sponsored. Each one links to the guide that explains it.

How much room you have to adjust

Espresso → filter2.6numbers of adjustment across the fine half of the dial
Filter → coarse7.4numbers covering filter through to cold brew
Curvelinearflat burrs, interpolated linearly

That is the resolution you actually have to work with on the Ode Gen 1. Where the number is small, a single step moves the cup more than you would expect — so change one at a time and taste before moving again.

Dialing in the Ode Gen 1

The original Ode had noticeably more fines than the Gen 2 that replaced it, which is why the Gen 2 burr upgrade became such a common retrofit. If you are running Gen 1 burrs, expect to sit slightly coarser than published Ode numbers to get the same cup.

Coming from another grinder?

Convert a grind setting to the Ode Gen 1

If a recipe quotes a setting for a different grinder, this maps it onto the Ode Gen 1’s dial using the same curve the chart above is built from.

Converting between two grinders that are not this one? Open the full converter.

Owners’ particle-size readings

No readings for the Ode Gen 1 yet. If you own one, you can measure your grind with a phone photo; readings are reviewed, then shown here.

How these numbers were worked out

Every grinder gets mapped onto a shared 0–100 grind index, where 0 is espresso-fine and 100 is the coarsest useful setting. Five reference points on the Ode Gen 1 are placed on that scale — espresso, moka, filter, French press and coarse — and the settings in between are interpolated.

Fellow publishes its own brew-method chart for the Ode Gen 1, and we checked every number against it. The chart above prints Fellow’s settings for the methods it names, and the reference points are fitted so the curve follows them; the other methods, and every conversion to and from this grinder, are read off that curve. Source: Ode Brew Grinder Quick Start and Brewing Guide, p.6 'Grind settings'.

The Ode Gen 1’s dial is interpolated linearly between those reference points, which is the right model for its burr geometry.

The result is that “medium-fine” resolves to a real number on this grinder rather than a vague instruction. It is a starting point, not a guarantee — burr wear, bean density and roast level all move the target, which is why every row above gives a range as well as a number.

Corrections to this page

  • 2026-10-23For every grinder whose maker publishes a brew-method chart, the chart now prints the maker’s own settings for the methods it names, checked against the maker’s document, and the rest follow a dial curve fitted through them. Per-setting micron figures are gone; particle sizes are given only for espresso, drip and cupping, where independent sources agree.
  • 2026-10-22Written as the number and which mark after it, the way owners count them: on an Ode, 4, 4.1, 4.2, then 5; on an Opus, up to 4.3. The positions themselves did not change. A setting typed as 4.2 for these grinders is now read as the second mark.
Every correction, with what the page said before →

Own a Ode Gen 1? Tell us your setting

If you’ve dialled in a method on your own Ode Gen 1, the number you landed on is the best evidence there is. Readings are checked by hand before anything changes here.

← All grinder charts